|
The [organization] shall identify the applicable physical and environmental protection policies covering the development environment and spacecraft hardware. {PE-1,PE-14,SA-3,SA-3(1),SA-10(3)}
|
|
|
The [organization] shall develop and document program-specific identification and authentication policies for accessing the development environment and spacecraft. {AC-3,AC-14,IA-1,SA-3,SA-3(1)}
|
|
|
The [organization] shall protect documentation and Controlled Unclassified Information (CUI) as required, in accordance with the risk management strategy.{AC-3,CM-12,CP-2,PM-17,RA-5(4),SA-3,SA-3(1),SA-5,SA-10,SC-8(1),SC-28(3),SI-12}
|
|
|
The [organization] shall identify and properly classify mission sensitive design/operations information and access control shall be applied in accordance with classification guides and applicable federal laws, Executive Orders, directives, policies, regulations, and standards.{SV-CF-3,SV-AV-5}{AC-3,CM-12,CP-2,PM-17,RA-5(4),SA-3,SA-3(1),SA-5,SA-8(19),SC-8(1),SC-28(3),SI-12}
|
* Mission sensitive information should be classified as Controlled Unclassified Information (CUI) or formally known as Sensitive but Unclassified. Ideally these artifacts would be rated SECRET or higher and stored on classified networks. Mission sensitive information can typically include a wide range of candidate material: the functional and performance specifications, the RF ICDs, databases, scripts, simulation and rehearsal results/reports, descriptions of uplink protection including any disabling/bypass features, failure/anomaly resolution, and any other sensitive information related to architecture, software, and flight/ground /mission operations. This could all need protection at the appropriate level (e.g., unclassified, SBU, classified, etc.) to mitigate levels of cyber intrusions that may be conducted against the project’s networks. Stand-alone systems and/or separate database encryption may be needed with controlled access and on-going Configuration Management to ensure changes in command procedures and critical database areas are tracked, controlled, and fully tested to avoid loss of science or the entire mission.
|
|
The [organization] shall ensure security requirements/configurations are placed in accordance with NIST 800-171 with enhancements in 800-172 on the development environments to prevent the compromise of source code from supply chain or information leakage perspective.{AC-3,SA-3,SA-3(1),SA-15}
|
|
|
The [organization] shall employ independent third-party analysis and penetration testing of all software (COTS, FOSS, Custom) associated with the system, system components, or system services.{CA-2,CA-2(1),CA-8(1),CM-10(1),SA-9,SA-11(3),SA-12(11),SI-3,SI-3(10),SR-4(4),SR-6(1)}
|
|
|
In coordination with [organization], the [organization] shall prioritize and remediate flaws identified during security testing/evaluation.{CA-2,CA-5,SA-11,SI-3,SI-3(10)}
|
|
|
The [organization] shall implement a verifiable flaw remediation process into the developmental and operational configuration management process.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CA-2,CA-5,SA-3,SA-3(1),SA-11,SI-3,SI-3(10)}
|
The verifiable process should also include a cross reference to mission objectives and impact statements. Understanding the flaws discovered and how they correlate to mission objectives will aid in prioritization.
|
|
The [organization] shall verify that the scope of security testing/evaluation provides complete coverage of required security controls (to include abuse cases and penetration testing) at the depth of testing defined in the test documents.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CA-2,CA-8,RA-5(3),SA-11(5),SA-11(7)}
|
* The frequency of testing should be driven by Program completion events and updates.
* Examples of approaches are static analyses, dynamic analyses, binary analysis, or a hybrid of the three approaches
|
|
The [organization] shall maintain evidence of the execution of the security assessment plan and the results of the security testing/evaluation.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CA-2,CA-8,SA-11}
|
|
|
The [organization] shall create and implement a security assessment plan that includes: (1) The types of analyses, testing, evaluation, and reviews of all software and firmware components; (2) The degree of rigor to be applied to include abuse cases and/or penetration testing; and (3) The types of artifacts produced during those processes.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CA-2,CA-8,SA-11,SA-11(5)}
|
The security assessment plan should include evaluation of mission objectives in relation to the security of the mission. Assessments should not only be control based but also functional based to ensure mission is resilient against failures of controls.
|
|
The [organization] shall determine the vulnerabilities/weaknesses that require remediation, and coordinate the timeline for that remediation, in accordance with the analysis of the vulnerability scan report, the mission assessment of risk, and mission needs.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CA-5,CM-3,RA-5,RA-7,SI-3,SI-3(10)}
|
|
|
The [organization] shall employ dynamic analysis (e.g.using simulation, penetration testing, fuzzing, etc.) to identify software/firmware weaknesses and vulnerabilities in developed and incorporated code (open source, commercial, or third-party developed code).{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CA-8,CM-10(1),RA-3(1),SA-11(5),SA-11(8),SA-11(9),SI-3,SI-7(10)}
|
|
|
The [organization] shall establish robust procedures and technical methods to perform testing to include adversarial testing (i.e.abuse cases) of the platform hardware and software.{CA-8,CP-4(5),RA-5,RA-5(1),RA-5(2),SA-3,SA-4(3),SA-11,SA-11(1),SA-11(2),SA-11(5),SA-11(7),SA-11(8),SA-15(7)}
|
|
|
The [organization] shall perform penetration testing/analysis: (1) On potential system elements before accepting the system; (2) As a realistic simulation of the active adversary’s known adversary tactics, techniques, procedures (TTPs), and tools; and (3) Throughout the lifecycle on physical and logical systems, elements, and processes.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{CA-8(1),SA-9,SA-11(5),SR-5(2)}
|
Penetration testing should be performed throughout the lifecycle on physical and logical systems, elements, and processes including: (1) Hardware, software, and firmware development processes; (2) Shipping/handling procedures; (3) Personnel and physical security programs; (4) Configuration management tools/measures to maintain provenance; and (5) Any other programs, processes, or procedures associated with the production/distribution of supply chain elements.
|
|
The [organization] shall develop and document program-specific configuration management policies and procedures for the hardware and software for the spacecraft. {CM-1,CM-3,CM-5(6),SA-10,SA-10(3)}
|
|
|
The [organization] shall perform software component analysis (a.k.a.origin analysis) for developed or acquired software.{CM-10,CM-10(1),RA-3(1),RA-5,SA-15(7),SI-3,SI-3(10),SR-4(4)}
|
|
|
The [organization] shall maintain a list of suppliers and potential suppliers used, and the products that they supply to include software.{SV-SP-3,SV-SP-4,SV-SP-11}{CM-10,PL-8(2),PM-30,SA-8(9),SA-8(11)}
|
Ideally you have diversification with suppliers
|
|
The [organization] shall test software and firmware updates related to flaw remediation for effectiveness and potential side effects on mission systems in a separate test environment before installation.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CM-3,CM-3(1),CM-3(2),CM-4(1),CM-4(2),CM-10(1),SA-8(31),SA-11(9),SI-2,SI-3,SI-3(10),SI-7(10),SI-7(12),SR-5(2)}
|
This requirement is focused on software and firmware flaws. If hardware flaw remediation is required, refine the requirement to make this clear.
|
|
The [organization] shall define processes and procedures to be followed when integrity verification tools detect unauthorized changes to software, firmware, and information.{SV-IT-2}{CM-3,CM-3(1),CM-3(5),CM-5(6),CM-6,CP-2,IR-6,IR-6(2),PM-30,SC-16(1),SC-51,SI-3,SI-4(7),SI-4(24),SI-7,SI-7(7),SI-7(10)}
|
|
|
The [organization] shall release updated versions of the mission information systems incorporating security-relevant software and firmware updates, after suitable regression testing, at a frequency no greater than [Program-defined frequency [90 days]].{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CM-3(2),CM-4(1)}
|
On-orbit patching/upgrades may be necessary if vulnerabilities are discovered after launch. The system should have the ability to update software post-launch.
|
|
The [organization] shall develop and implement anti-counterfeit policy and procedures designed to detect and prevent counterfeit components from entering the information system, including support tamper resistance and provide a level of protection against the introduction of malicious code or hardware.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{CM-3(8),CM-7(9),PM-30,SA-8(9),SA-8(11),SA-9,SA-10(3),SA-19,SC-51,SR-4(3),SR-4(4),SR-5(2),SR-11}
|
|
|
The [organization] shall develop and document spacecraft integrity policies covering both hardware and software. {CM-5(6),SA-10(3),SI-1,SI-7(12)}
|
|
|
The [organization] shall maintain the integrity of the mapping between the master build data (hardware drawings and software/firmware code) describing the current version of hardware, software, and firmware and the on-site master copy of the data for the current version.{CM-6,SA-8(21),SA-8(30),SA-10,SA-10(3),SA-10(4),SA-10(5),SI-7(10),SR-4(4)}
|
|
|
The [organization] shall prohibit the use of binary or machine-executable code from sources with limited or no warranty and without the provision of source code.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CM-7(8)}
|
|
|
The [organization] prohibits the use of binary or machine-executable code from sources with limited or no warranty and without the provision of source code.{CM-7(8),CM-7(8),CM-10(1),SA-8(9),SA-8(11),SA-10(2),SI-3,SR-4(4)}
|
|
|
The [organization] shall conduct a criticality analysis to identify mission critical functions and critical components and reduce the vulnerability of such functions and components through secure system design.{SV-SP-3,SV-SP-4,SV-AV-7,SV-MA-4}{CP-2,CP-2(8),PL-7,PM-11,PM-30(1),RA-3(1),RA-9,SA-8(9),SA-8(11),SA-8(25),SA-12,SA-14,SA-15(3),SC-7(29),SR-1}
|
During SCRM, criticality analysis will aid in determining supply chain risk. For mission critical functions/components, extra scrutiny must be applied to ensure supply chain is secured.
|
|
The [organization] shall employ techniques to limit harm from potential adversaries identifying and targeting the [organization]s supply chain.{CP-2,PM-30,SA-9,SA-12(5),SC-38,SR-3,SR-3(1),SR-3(2),SR-5(2)}
|
|
|
The [organization] shall employ Operations Security (OPSEC) safeguards to protect supply chain-related information for the system, system components, or system services. {CP-2(8),PM-30,SA-12(9),SC-38,SR-7}
|
|
|
The [organization] shall report counterfeit information system components to [organization] officials. {SV-SP-4}{IR-6,IR-6(2),PM-30,SA-19,SR-11}
|
|
|
The [organization] shall report identified systems or system components containing software affected by recently announced cybersecurity-related software flaws (and potential vulnerabilities resulting from those flaws) to [organization] officials with cybersecurity responsibilities.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-11}{IR-6,IR-6(2),SI-2,SI-3,SI-4(12),SR-4(4)}
|
|
|
The [organization] shall document the platform's security architecture, and how it is established within and is an integrated part of the overall [organization] mission security architecture.{PL-7,SA-8(7),SA-8(13),SA-8(29),SA-8(30),SA-17}
|
|
|
The [organization] shall use all-source intelligence analysis of suppliers and potential suppliers of the information system, system components, or system services to inform engineering, acquisition, and risk management decisions.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{PM-16,PM-30,RA-2,RA-3(1),RA-3(2),RA-7,SA-9,SA-12(8),SR-5(2)}
|
* The Program should also consider sub suppliers and potential sub suppliers.
* All-source intelligence of suppliers that the organization may use includes: (1) Defense Intelligence Agency (DIA) Threat Assessment Center (TAC), the enterprise focal point for supplier threat assessments for the DOD acquisition community risks; (2) Other U.S. Government resources including: (a) Government Industry Data Exchange Program (GIDEP) – Database where government and industry can record issues with suppliers, including counterfeits; and (b) System for Award Management (SAM) – Database of companies that are barred from doing business with the US Government.
|
|
The [organization] shall request threat analysis of suppliers of critical components and manage access to and control of threat analysis products containing U.S.person information.{SV-SP-3,SV-SP-4,SV-SP-11}{PM-16,PM-30(1),RA-3(1),SA-9,SA-12,SR-1}
|
The intent of this requirement is to address supply chain concerns on hardware and software vendors. Not required for trusted suppliers accredited to the Defense Microelectronic Activity (DMEA). If the Program intends to use a supplier not accredited by DMEA, the government customer should be notified as soon as possible. If the Program has internal processes to vet suppliers, it may meet this requirement. All software used and its origins must be included in the SBOM and be subjected to internal and Government vulnerability scans.
|
|
The [organization] shall conduct a supplier review prior to entering into a contractual agreement with a sub [organization] to acquire systems, system components, or system services.{PM-30,PM-30(1),RA-3(1),SA-8(9),SA-8(11),SA-9,SA-12(2),SR-5(2),SR-6}
|
|
|
The [organization] shall maintain documentation tracing the strategies, tools, and methods implemented to mitigate supply chain risk .{SV-SP-3,SV-SP-4,SV-AV-7}{PM-30,RA-3(1),SA-12(1),SR-5}
|
Examples include: (1) Transferring a portion of the risk to the developer or supplier through the use of contract language and incentives; (2) Using contract language that requires the implementation of SCRM throughout the system lifecycle in applicable contracts and other acquisition and assistance instruments (grants, cooperative agreements, Cooperative Research and Development Agreements (CRADAs), and other transactions). Within the DOD some examples include: (a) Language outlined in the Defense Acquisition Guidebook section 13.13. Contracting; (b) Language requiring the use of protected mechanisms to deliver elements and data about elements, processes, and delivery mechanisms; (c) Language that articulates that requirements flow down supply chain tiers to sub-prime suppliers. (3) Incentives for suppliers that: (a) Implement required security safeguards and SCRM best practices; (b) Promote transparency into their organizational processes and security practices; (c) Provide additional vetting of the processes and security practices of subordinate suppliers, critical information system components, and services; and (d) Implement contract to reduce SC risk down the contract stack. (4) Gaining insight into supplier security practices; (5) Using contract language and incentives to enable more robust risk management later in the lifecycle; (6) Using a centralized intermediary or “Blind Buy” approaches to acquire element(s) to hide actual usage locations from an untrustworthy supplier or adversary;
|
|
The [organization] shall protect against supply chain threats to the system, system components, or system services by employing security safeguards as defined by NIST SP 800-161 Rev.1.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{PM-30,RA-3(1),SA-8(9),SA-8(11),SA-12,SI-3,SR-1}
|
The chosen supply chain safeguards should demonstrably support a comprehensive, defense-in-breadth information security strategy. Safeguards should include protections for both hardware and software. Program should define their critical components (HW & SW) and identify the supply chain protections, approach/posture/process.
|
|
The [organization] shall use the threat and vulnerability analyses of the as-built system, system components, or system services to inform and direct subsequent testing/evaluation of the as-built system, component, or service.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{RA-3(3),SA-11(2),SA-15(8),SI-3}
|
|
|
The [organization] shall ensure that the vulnerability scanning tools (e.g., static analysis and/or component analysis tools) used include the capability to readily update the list of potential information system vulnerabilities to be scanned.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{RA-5,RA-5(1),RA-5(3),SI-3}
|
|
|
The [organization] shall perform vulnerability analysis and risk assessment of all systems and software.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{RA-5,RA-5(3),SA-15(7),SI-3}
|
|
|
The [organization] shall ensure that vulnerability scanning tools and techniques are employed that facilitate interoperability among tools and automate parts of the vulnerability management process by using standards for: (1) Enumerating platforms, custom software flaws, and improper configurations; (2) Formatting checklists and test procedures; and (3) Measuring vulnerability impact.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{RA-5,RA-5(3),SI-3}
|
Component/Origin scanning looks for open-source libraries/software that may be included into the baseline and looks for known vulnerabilities and open-source license violations.
|
|
The [organization] shall perform static binary analysis of all firmware that is utilized on the spacecraft.{SV-SP-7,SV-SP-11}{RA-5,SA-10,SA-11,SI-7(10)}
|
Many commercial products/parts are utilized within the system and should be analyzed for security weaknesses. Blindly accepting the firmware is free of weakness is unacceptable for high assurance missions. The intent is to not blindly accept firmware from unknown sources and assume it is secure. This is meant to apply to firmware the vendors are not developing internally. In-house developed firmware should be going through the vendor's own testing program and have high assurance it is secure. When utilizing firmware from other sources, "expecting" does not meet this requirement. Each supplier needs to provide evidence to support that claim that their firmware they are getting is genuine and secure.
|
|
The [organization] shall perform static source code analysis for all available source code looking for [[organization]-defined Top CWE List] weaknesses using complimentary set of static code analysis tools (i.e.more than one).{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{RA-5,SA-11(1),SA-15(7)}
|
|
|
The [organization] shall analyze vulnerability/weakness scan reports and results from security control assessments.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{RA-5,SI-3}
|
|
|
The [organization] shall ensure that the list of potential system vulnerabilities scanned is updated [prior to a new scan] {SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{RA-5(2),SI-3}
|
|
|
The [organization] shall perform configuration management during system, component, or service during [design; development; implementation; operations].{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-10}
|
|
|
The [organization] shall review proposed changes to the spacecraft, assessing both mission and security impacts.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-10,CM-3(2)}
|
|
|
The [organization] shall correct flaws identified during security testing/evaluation.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-11}
|
Flaws that impact the mission objectives should be prioritized.
|
|
The [organization] shall perform [Selection (one or more): unit; integration; system; regression] testing/evaluation at [Program-defined depth and coverage].{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-11}
|
The depth needs to include functional testing as well as negative/abuse testing.
|
|
The [organization] shall create prioritized list of software weakness classes (e.g., Common Weakness Enumerations) to be used during static code analysis for prioritization of static analysis results.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-11(1),SA-15(7)}
|
The prioritized list of CWEs should be created considering operational environment, attack surface, etc. Results from the threat modeling and attack surface analysis should be used as inputs into the CWE prioritization process. There is also a CWSS (https://cwe.mitre.org/cwss/cwss_v1.0.1.html) process that can be used to prioritize CWEs. The prioritized list of CWEs can help with tools selection as well as you select tools based on their ability to detect certain high priority CWEs.
|
|
The [organization] shall use threat modeling and vulnerability analysis to inform the current development process using analysis from similar systems, components, or services where applicable.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-11(2),SA-15(8)}
|
|
|
The [organization] shall perform and document threat and vulnerability analyses of the as-built system, system components, or system services.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-11(2),SI-3}
|
|
|
The [organization] shall perform a manual code review of all flight code.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-11(4)}
|
|
|
The [organization] shall perform manual code review of all produced code looking for quality, maintainability, and security flaws.{SA-11(4),SI-3,SI-3(10),SR-4(4)}
|
|
|
The [organization] shall conduct an Attack Surface Analysis and reduce attack surfaces to a level that presents a low level of compromise by an attacker.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-11(6),SA-15(5)}
|
|
|
The [organization] shall define acceptable coding languages to be used by the software developer.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-15}
|
|
|
The [organization] shall define acceptable secure coding standards for use by the software developers.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-15}
|
|
|
The [organization] shall have automated means to evaluate adherence to coding standards.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-15,SA-15(7),RA-5}
|
Manual review cannot scale across the code base; you must have a way to scale in order to confirm your coding standards are being met. The intent is for automated means to ensure code adheres to a coding standard.
|
|
The [organization] shall perform component analysis (a.k.a.origin analysis) for developed or acquired software.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-15(7),RA-5}
|
|
|
The [organization] shall require subcontractors developing information system components or providing information system services (as appropriate) to demonstrate the use of a system development life cycle that includes [state-of-the-practice system/security engineering methods, software development methods, testing/evaluation/validation techniques, and quality control processes].{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-9}{SA-3,SA-4(3)}
|
Select the particular subcontractors, software vendors, and manufacturers based on the criticality analysis performed for the Program Protection Plan and the criticality of the components that they supply.
|
|
The [organization] shall ensure that all Electrical, Electronic, Electro-mechanical & Electro-optical (EEEE) and mechanical piece parts procured from the Original Component Manufacturer (OCM) or their authorized distribution network.{SA-8(9),SA-8(11),SA-12,SA-12(1),SC-16(1),SR-1,SR-5}
|
|
|
The [organization] shall use a certified environment to develop, code and test executable software (firmware or bit-stream) that will be programmed into a one-time programmable FPGA or be programmed into non-volatile memory (NVRAM) that the FPGA executes.{SA-8(9),SA-8(11),SA-12,SA-12(1),SC-51,SI-7(10),SR-1,SR-5}
|
|
|
The [organization] shall ensure that all ASICs designed, developed, manufactured, packaged, and tested by suppliers with a Defense Microelectronics Activity (DMEA) Trust accreditation.{spacecraft-SP-5} {SA-8(9),SA-8(11),SA-12,SA-12(1),SR-1,SR-5}
|
|
|
The [organization] shall correct reported cybersecurity-related information system flaws.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SI-2}
|
* Although this requirement is stated to specifically apply to cybersecurity-related flaws, the Program office may choose to broaden it to all SV flaws.
* This requirement is allocated to the Program, as it is presumed, they have the greatest knowledge of the components of the system and when identified flaws apply.
|
|
The [organization] shall identify, report, and coordinate correction of cybersecurity-related information system flaws.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SI-2}
|
|
|
If using the Government Microelectronics Assessment for Trust (GOMAT) framework outright, to perform ASIC and FPGA threat/vulnerability risk assessment, the following requirements would apply: {SV-SP-5}{SR-1,SR-5}
|
• 1.g “In coordination with the DOD CIO, the Director, Defense Intelligence Agency (DIA), and the Heads of the DOD Components, develop a strategy for managing risk in the supply chain for integrated circuit-related products and services (e.g., FPGAs, printed circuit boards) that are identifiable to the supplier as specifically created or modified for DOD (e.g., military temperature range, radiation hardened).
|
|
The [organization] shall develop and implement anti-counterfeit policy and procedures, in coordination with the [CIO], that is demonstrably consistent with the anti-counterfeit policy defined by the Program office.{SV-SP-4,SV-SP-11}{SR-11}
|
|
|
The [organization] shall develop a plan for managing supply chain risks associated with the research and development, design, manufacturing, acquisition, delivery, integration, operations and maintenance, and disposal of organization-defined systems, system components, or system services.{SR-2}
|
|
|
The [organization] shall protect the supply chain risk management plan from unauthorized disclosure and modification.{SR-2}
|
|
|
The [organization] shall review and update the supply chain risk management plan as required, to address threats, organizational, or environmental changes.{SR-2}
|
|
|
The [organization] shall establish a supply chain risk management team to lead and support supply chain risk management activities.{SR-2(1)}
|
|
|
The [organization] shall employ [organization]-defined techniques to limit harm from potential adversaries identifying and targeting the Program supply chain.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{SR-3(2),SC-38}
|
Examples of security safeguards that the organization should consider implementing to limit the harm from potential adversaries targeting the organizational supply chain, are: (1) Using trusted physical delivery mechanisms that do not permit access to the element during delivery (ship via a protected carrier, use cleared/official couriers, or a diplomatic pouch); (2) Using trusted electronic delivery of products and services (require downloading from approved, verification-enhanced sites); (3) Avoiding the purchase of custom configurations, where feasible; (4) Using procurement carve outs (i.e., exclusions to commitments or obligations), where feasible; (5) Using defensive design approaches; (6) Employing system OPSEC principles; (7) Employing a diverse set of suppliers; (8) Employing approved vendor lists with standing reputations in industry; (9) Using a centralized intermediary and “Blind Buy” approaches to acquire element(s) to hide actual usage locations from an untrustworthy supplier or adversary Employing inventory management policies and processes; (10) Using flexible agreements during each acquisition and procurement phase so that it is possible to meet emerging needs or requirements to address supply chain risk without requiring complete revision or re-competition of an acquisition or procurement; (11) Using international, national, commercial or government standards to increase potential supply base; (12) Limiting the disclosure of information that can become publicly available; and (13) Minimizing the time between purchase decisions and required delivery.
|
|
The [organization] shall employ the [organization]-defined approaches for the purchase of the system, system components, or system services from suppliers.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{SR-5}
|
This could include tailored acquisition strategies, contract tools, and procurement methods.
|
|
The [organization] (and Prime Contractor) shall conduct a supplier review prior to entering into a contractual agreement with a contractor (or sub-contractor) to acquire systems, system components, or system services.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{SR-6}
|
|
|
The [organization] shall employ [Selection (one or more): independent third-party analysis, Program penetration testing, independent third-party penetration testing] of [Program-defined supply chain elements, processes, and actors] associated with the system, system components, or system services.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{SR-6(1)}
|
|
|
The [organization] shall employ [Program-defined Operations Security (OPSEC) safeguards] to protect supply chain-related information for the system, system components, or system services.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{SR-7,SC-38,CP-2(8)}
|
OPSEC safeguards may include: (1) Limiting the disclosure of information needed to design, develop, test, produce, deliver, and support the element for example, supplier identities, supplier processes, potential suppliers, security requirements, design specifications, testing and evaluation result, and system/component configurations, including the use of direct shipping, blind buys, etc.; (2) Extending supply chain awareness, education, and training for suppliers, intermediate users, and end users; (3) Extending the range of OPSEC tactics, techniques, and procedures to potential suppliers, contracted suppliers, or sub-prime contractor tier of suppliers; and (4) Using centralized support and maintenance services to minimize direct interactions between end users and original suppliers.
|
|
The [organization] shall enable integrity verification of hardware components.{SA-10(3),SA-8(21),SA-10(3),SC-51}
|
* The integrity verification mechanisms may include:
** Stipulating and monitoring logical delivery of products and services, requiring downloading from approved, verification-enhanced sites;
** Encrypting elements (software, software patches, etc.) and supply chain process data in transit (motion) and at rest throughout delivery;
** Requiring suppliers to provide their elements “secure by default”, so that additional configuration is required to make the element insecure;
** Implementing software designs using programming languages and tools that reduce the likelihood of weaknesses;
** Implementing cryptographic hash verification; and
** Establishing performance and sub-element baseline for the system and system elements to help detect unauthorized tampering/modification during repairs/refurbishing.
** Stipulating and monitoring logical delivery of products and services, requiring downloading from approved, verification-enhanced sites;
** Encrypting elements (software, software patches, etc.) and supply chain process data in transit (motion) and at rest throughout delivery;
** Requiring suppliers to provide their elements “secure by default”, so that additional configuration is required to make the element insecure;
** Implementing software designs using programming languages and tools that reduce the likelihood of weaknesses;
** Implementing cryptographic hash verification; and
** Establishing performance and sub-element baseline for the system and system elements to help detect unauthorized tampering/modification during repairs/refurbishing.
|
|
The [organization] shall enable integrity verification of software and firmware components.{SV-IT-2}{CM-3(5),CM-5(6),CM-10(1),SA-8(9),SA-8(11),SA-8(21),SA-10(1),SI-3,SI-4(24),SI-7,SI-7(10),SI-7(12),SR-4(4)}
|
* The integrity verification mechanisms may include:
** Stipulating and monitoring logical delivery of products and services, requiring downloading from approved, verification-enhanced sites;
** Encrypting elements (software, software patches, etc.) and supply chain process data in transit (motion) and at rest throughout delivery;
** Requiring suppliers to provide their elements “secure by default”, so that additional configuration is required to make the element insecure;
** Implementing software designs using programming languages and tools that reduce the likelihood of weaknesses;
** Implementing cryptographic hash verification; and
** Establishing performance and sub-element baseline for the system and system elements to help detect unauthorized tampering/modification during repairs/refurbishing.
** Stipulating and monitoring logical delivery of products and services, requiring downloading from approved, verification-enhanced sites;
** Encrypting elements (software, software patches, etc.) and supply chain process data in transit (motion) and at rest throughout delivery;
** Requiring suppliers to provide their elements “secure by default”, so that additional configuration is required to make the element insecure;
** Implementing software designs using programming languages and tools that reduce the likelihood of weaknesses;
** Implementing cryptographic hash verification; and
** Establishing performance and sub-element baseline for the system and system elements to help detect unauthorized tampering/modification during repairs/refurbishing.
|
|
For FPGA pre-silicon artifacts that are developed, coded, and tested by a developer that is not accredited, the [organization] shall be subjected to a development environment and pre-silicon artifacts risk assessment by [organization]. Based on the results of the risk assessment, the [organization] may need to implement protective measures or other processes to ensure the integrity of the FPGA pre-silicon artifacts.{SV-SP-5}{SA-3,SA-3(1),SA-8(9),SA-8(11),SA-12,SA-12(1),SR-1,SR-5}
|
DOD-I-5200.44 requires the following:
4.c.2 “Control the quality, configuration, and security of software, firmware, hardware, and systems throughout their lifecycles... Employ protections that manage risk in the supply chain… (e.g., integrated circuits, field-programmable gate arrays (FPGA), printed circuit boards) when they are identifiable (to the supplier) as having a DOD end-use. “ 4.e “In applicable systems, integrated circuit-related products and services shall be procured from a Trusted supplier accredited by the Defense Microelectronics Activity (DMEA) when they are custom-designed, custommanufactured, or tailored for a specific DOD military end use (generally referred to as application-specific integrated circuits (ASIC)). “ 1.g “In coordination with the DOD CIO, the Director, Defense Intelligence Agency (DIA), and the Heads of the DOD Components, develop a strategy for managing risk in the supply chain for integrated circuit-related products and services (e.g., FPGAs, printed circuit boards) that are identifiable to the supplier as specifically created or modified for DOD (e.g., military temperature range, radiation hardened).
|
|
The [organization] shall require the developer of the system, system component, or system services to demonstrate the use of a system development life cycle that includes [state-of-the-practice system/security engineering methods, software development methods, testing/evaluation/validation techniques, and quality control processes].{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-9}{SA-3,SA-4(3)}
|
Examples of good security practices would be using defense-in-depth tactics across the board, least-privilege being implemented, two factor authentication everywhere possible, using DevSecOps, implementing and validating adherence to secure coding standards, performing static code analysis, component/origin analysis for open source, fuzzing/dynamic analysis with abuse cases, etc.
|
|
Any EEEE or mechanical piece parts that cannot be procured from the OCM or their authorized distribution network shall be approved and the government program office notified to prevent and detect counterfeit and fraudulent parts and materials.{SV-SP-5}{SA-8(9),SA-8(11),SA-12,SA-12(1),SR-1,SR-5}
|
The Program, working with the contractors, shall identify which ASICs/FPGAs perform or execute an integral part of mission critical functions and if the supplier is accredited “Trusted” by DMEA. If the contractor is not accredited by DMEA, then the Program may apply various of the below ASIC/FPGA assurance requirements to the contractor, and the Program may need to perform a risk assessment of the contractor’s design environment.
|
|
For ASICs that are designed, developed, manufactured, packaged, or tested by a supplier that is not DMEA accredited, the ASIC development shall undergo a threat/vulnerability risk assessment. Based on the results of the risk assessment, the [organization] may need to implement protective measures or other processes to ensure the integrity of the ASIC.{SV-SP-5}{SA-8(9),SA-8(11),SA-8(21),SA-12,SA-12(1),SR-1,SR-4(4),SR-5}
|
DOD-I-5200.44 requires the following:
4.c.2 “Control the quality, configuration, and security of software, firmware, hardware, and systems throughout their lifecycles... Employ protections that manage risk in the supply chain… (e.g., integrated circuits, field-programmable gate arrays (FPGA), printed circuit boards) when they are identifiable (to the supplier) as having a DOD end-use. “ 4.e “In applicable systems, integrated circuit-related products and services shall be procured from a Trusted supplier accredited by the Defense Microelectronics Activity (DMEA) when they are custom-designed, custommanufactured, or tailored for a specific DOD military end use (generally referred to as application-specific integrated circuits (ASIC)). “ 1.g “In coordination with the DOD CIO, the Director, Defense Intelligence Agency (DIA), and the Heads of the DOD Components, develop a strategy for managing risk in the supply chain for integrated circuit-related products and services (e.g., FPGAs, printed circuit boards) that are identifiable to the supplier as specifically created or modified for DOD (e.g., military temperature range, radiation hardened).
|
|
Any EEEE or mechanical piece parts that cannot be procured from the OCM or their authorized franchised distribution network shall be approved by the [organization]’s Parts, Materials and Processes Control Board (PMPCB) as well as the government program office to prevent and detect counterfeit and fraudulent parts and materials.{SV-SP-5}{SR-1,SR-5}
|
The Program, working with the contractors, shall identify which ASICs/FPGAs perform or execute an integral part of mission critical functions and if the supplier is accredited “Trusted” by DMEA. If the contractor is not accredited by DMEA, then the Program may apply various of the below ASIC/FPGA assurance requirements to the contractor, and the Program may need to perform a risk assessment of the contractor’s design environment.
|
|
For ASICs that are designed, developed, manufactured, packaged, or tested by a supplier that is NOT DMEA accredited Trusted, the ASIC development shall undergo a threat/vulnerability risk assessment.The assessment shall use Aerospace security guidance and requirements tailored from TOR-2019-00506 Vol.2, and TOR-2019-02543 ASIC and FPGA Risk Assessment Process and Checklist.Based on the results of the risk assessment, the Program may require the developer to implement protective measures or other processes to ensure the integrity of the ASIC.{SV-SP-5}{SR-1,SR-5}
|
DOD-I-5200.44 requires the following:
4.c.2 “Control the quality, configuration, and security of software, firmware, hardware, and systems throughout their lifecycles... Employ protections that manage risk in the supply chain… (e.g., integrated circuits, field-programmable gate arrays (FPGA), printed circuit boards) when they are identifiable (to the supplier) as having a DOD end-use. “ 4.e “In applicable systems, integrated circuit-related products and services shall be procured from a Trusted supplier accredited by the Defense Microelectronics Activity (DMEA) when they are custom-designed, custommanufactured, or tailored for a specific DOD military end use (generally referred to as application-specific integrated circuits (ASIC)). “ 1.g “In coordination with the DOD CIO, the Director, Defense Intelligence Agency (DIA), and the Heads of the DOD Components, develop a strategy for managing risk in the supply chain for integrated circuit-related products and services (e.g., FPGAs, printed circuit boards) that are identifiable to the supplier as specifically created or modified for DOD (e.g., military temperature range, radiation hardened).
|
|
For FPGA pre-silicon artifacts that are developed, coded, and tested by a developer that is NOT DMEA accredited Trusted, the contractor/developer shall be subjected to a development environment and pre-silicon artifacts risk assessment by the Program.The assessment shall use Aerospace security guidance and requirements in TOR-2019-00506 Vol.2, and TOR-2019-02543 ASIC and FPGA Risk Assessment Process and Checklist.Based on the results of the risk assessment, the Program may require the developer to implement protective measures or other processes to ensure the integrity of the FPGA pre-silicon artifacts.{SV-SP-5}{SR-1,SR-5}
|
DOD-I-5200.44 requires the following:
4.c.2 “Control the quality, configuration, and security of software, firmware, hardware, and systems throughout their lifecycles... Employ protections that manage risk in the supply chain… (e.g., integrated circuits, field-programmable gate arrays (FPGA), printed circuit boards) when they are identifiable (to the supplier) as having a DOD end-use. “ 4.e “In applicable systems, integrated circuit-related products and services shall be procured from a Trusted supplier accredited by the Defense Microelectronics Activity (DMEA) when they are custom-designed, custommanufactured, or tailored for a specific DOD military end use (generally referred to as application-specific integrated circuits (ASIC)). “ 1.g “In coordination with the DOD CIO, the Director, Defense Intelligence Agency (DIA), and the Heads of the DOD Components, develop a strategy for managing risk in the supply chain for integrated circuit-related products and services (e.g., FPGAs, printed circuit boards) that are identifiable to the supplier as specifically created or modified for DOD (e.g., military temperature range, radiation hardened).
|
|
The [organization] shall ensure that the contractors/developers have all ASICs designed, developed, manufactured, packaged, and tested by suppliers with a Defense Microelectronics Activity (DMEA) Trust accreditation.{SV-SP-5}{SR-1,SR-5}
|
|
|
The [organization] shall ensure that the contractors/developers have all EEEE, and mechanical piece parts procured from the Original Component Manufacturer (OCM) or their authorized franchised distribution network.{SV-SP-5}{SR-1,SR-5}
|
These requirements might only make sense for ASIC/FPGA that are deemed to support mission critical functions. The Program has the responsibility to identify all ASICs and FPGAs that are used in all flight hardware by each hardware element. This list must include all contractor and subcontractor usage of ASICs and FPGAs.
|
|
The [organization] shall use a DMEA certified environment to develop, code and test executable software (firmware or bit-stream) that will be programmed into a one-time programmable FPGA or be programmed into non-volatile memory (NVRAM) that the FPGA executes.{SV-SP-5}{SR-1,SR-5}
|
DOD-I-5200.44 requires the following:
4.c.2 “Control the quality, configuration, and security of software, firmware, hardware, and systems throughout their lifecycles... Employ protections that manage risk in the supply chain… (e.g., integrated circuits, field-programmable gate arrays (FPGA), printed circuit boards) when they are identifiable (to the supplier) as having a DOD end-use. “ 4.e “In applicable systems, integrated circuit-related products and services shall be procured from a Trusted supplier accredited by the Defense Microelectronics Activity (DMEA) when they are custom-designed, custommanufactured, or tailored for a specific DOD military end use (generally referred to as application-specific integrated circuits (ASIC)). “ 1.g “In coordination with the DOD CIO, the Director, Defense Intelligence Agency (DIA), and the Heads of the DOD Components, develop a strategy for managing risk in the supply chain for integrated circuit-related products and services (e.g., FPGAs, printed circuit boards) that are identifiable to the supplier as specifically created or modified for DOD (e.g., military temperature range, radiation hardened).
|
|
The [spacecraft] shall employ the principle of least privilege, allowing only authorized accesses processes which are necessary to accomplish assigned tasks in accordance with system functions.{SV-AC-6}{AC-3,AC-6,AC-6(9),CA-9,CM-5,CM-5(5),CM-5(6),SA-8(2),SA-8(5),SA-8(6),SA-8(14),SA-8(23),SA-17(7),SC-2,SC-7(29),SC-32,SC-32(1),SI-3}
|
|
|
The [spacecraft] shall ensure that processes reusing a shared system resource (e.g., registers, main memory, secondary storage) do not have access to information (including encrypted representations of information) previously stored in that resource during a prior use by a process after formal release of that resource back to the system or reuse.{SV-AC-6}{AC-3,PM-32,SA-8(2),SA-8(5),SA-8(6),SA-8(19),SC-4,SI-3}
|
|
|
The [spacecraft] software subsystems shall provide non-identical methods, or functionally independent methods, for commanding a mission critical function when the software is the sole control of that function.{SV-MA-3,SV-AV-7}{AC-3(2)}
|
|
|
The [spacecraft] software subsystems shall provide two independent and unique command messages to deactivate a fault tolerant capability for a critical or catastrophic hazard.{SV-MA-3,SV-AV-7}{AC-3(2)}
|
|
|
The [spacecraft] shall require multi-factor authorization for all spacecraft [applications or operating systems] updates within the spacecraft.{SV-SP-9,SV-SP-11}{AC-3(2),CM-3(8),CM-5,PM-12,SA-8(8),SA-8(31),SA-10(2),SI-3(8),SI-7(12),SI-10(6)}
|
The intent is for multiple checks to be performed prior to executing these SV SW updates. One action is mere act of uploading the SW to the spacecraft. Another action could be check of digital signature (ideal but not explicitly required) or hash or CRC or a checksum. Crypto boxes provide another level of authentication for all commands, including SW updates but ideally there is another factor outside of crypto to protect against FSW updates. Multi-factor authorization could be the "two-man rule" where procedures are in place to prevent a successful attack by a single actor (note: development activities that are subsequently subject to review or verification activities may already require collaborating attackers such that a "two-man rule" is not appropriate).
|
|
The [spacecraft] shall implement boundary protections to separate bus, communications, and payload components supporting their respective functions.{SV-AC-6}{AC-3(3),AC-3(4),CA-9,SA-8(3),SA-8(14),SA-8(18),SA-8(19),SA-17(7),SC-2,SC-2(2),SC-7(13),SC-7(21),SC-7(29),SC-16(3),SC-32,SI-3,SI-4(13),SI-4(25)}
|
|
|
The [spacecraft] shall isolate mission critical functionality from non-mission critical functionality by means of an isolation boundary (e.g.via partitions) that controls access to and protects the integrity of, the hardware, software, and firmware that provides that functionality.{SV-AC-6}{AC-3(3),AC-3(4),CA-9,SA-8(3),SA-8(19),SA-17(7),SC-2,SC-3,SC-3(4),SC-7(13),SC-7(29),SC-32,SC-32(1),SI-3,SI-7(10),SI-7(12)}
|
|
|
The [spacecraft] shall prevent unauthorized access to system resources by employing an efficient capability based object model that supports both confinement and revocation of these capabilities when the platform security deems it necessary.{SV-AC-6}{AC-3(8),IA-4(9),PM-32,SA-8(2),SA-8(5),SA-8(6),SA-8(18),SA-8(19),SC-2(2),SC-4,SC-16,SC-32,SI-3}
|
|
|
The [spacecraft] shall monitor and collect all onboard cyber-relevant data (from multiple system components), including identification of potential attacks and sufficient information about the attack for subsequent analysis.{SV-DCO-1}{AC-6(9),AC-20,AC-20(1),AU-2,AU-12,IR-4,IR-4(1),RA-10,SI-3,SI-3(10),SI-4,SI-4(1),SI-4(2),SI-4(7),SI-4(24)}
|
The spacecraft will monitor and collect data that provides accountability of activity occurring onboard the spacecraft. Due to resource limitations on the spacecraft, analysis must be performed to determine which data is critical for retention and which can be filtered. Full system coverage of data and actions is desired as an objective; it will likely be impractical due to the resource limitations. “Cyber-relevant data” refers to all data and actions deemed necessary to support accountability and awareness of onboard cyber activities for the mission. This would include data that may indicate abnormal activities, critical configuration parameters, transmissions on onboard networks, command logging, or other such data items. This set of data items should be identified early in the system requirements and design phase. Cyber-relevant data should support the ability to assess whether abnormal events are unintended anomalies or actual cyber threats. Actual cyber threats may rarely or never occur, but non-threat anomalies occur regularly. The ability to filter out cyber threats for non-cyber threats in relevant time would provide a needed capability. Examples could include successful and unsuccessful attempts to access, modify, or delete privileges, security objects, security levels, or categories of information (e.g., classification levels).
|
|
The [spacecraft] shall generate cyber-relevant audit records containing information that establishes what type of event occurred, when the event occurred, where the event occurred, the source of the event, and the outcome of the event.{SV-DCO-1}{AU-3,AU-3(1),AU-12,IR-4,IR-4(1),RA-10,SI-3,SI-3(10),SI-4(7),SI-4(24)}
|
|
|
The [spacecraft] shall attribute cyber attacks and identify unauthorized use of the platform by downlinking onboard cyber information to the mission ground station within 3 minutes. {AU-4(1),IR-4,IR-4(1),IR-4(12),IR-4(13),RA-10,SA-8(22),SI-3,SI-3(10),SI-4(5),SI-4(7),SI-4(12),SI-4(24)}
|
|
|
The [spacecraft] shall alert in the event of the audit/logging processing failures.{AU-5,AU-5(1),AU-5(2),SI-3,SI-4,SI-4(1),SI-4(7),SI-4(12),SI-4(24)}
|
|
|
The [spacecraft] shall provide the capability of a cyber “black-box” to capture necessary data for cyber forensics of threat signatures and anomaly resolution when cyber attacks are detected.{SV-DCO-1}{AU-5(5),AU-9(2),AU-9(3),AU-12,IR-4(12),IR-4(13),IR-5(1),SI-3,SI-3(10),SI-4,SI-4(1),SI-4(7),SI-4(24),SI-7(7)}
|
Similar concept of a "black box" on an aircraft where all critical information is stored for post forensic analysis. Black box can be used to record CPU utilization, GNC physical parameters, audit records, memory contents, TT&C data points, etc. The timeframe is dependent upon implementation but needs to meet the intent of the requirement. For example, 30 days may suffice.
|
|
The [spacecraft] shall provide automated onboard mechanisms that integrate audit review, analysis, and reporting processes to support mission processes for investigation and response to suspicious activities to determine the attack class in the event of a cyber attack.{SV-DCO-1}{AU-6(1),IR-4,IR-4(1),IR-4(12),IR-4(13),PM-16(1),RA-10,SA-8(21),SA-8(22),SC-5(3),SI-3,SI-3(10),SI-4(7),SI-4(24),SI-7(7)}
|
* Identifying the class (e.g., exfiltration, Trojans, etc.), nature, or effect of cyberattack (e.g., exfiltration, subverted control, or mission interruption) is necessary to determine the type of response. The first order of identification may be to determine whether the event is an attack or a non-threat event (anomaly). The objective requirement would be to predict the impact of the detected signature.
* Unexpected conditions can include RF lockups, loss of lock, failure to acquire an expected contact and unexpected reports of acquisition, unusual AGC and ACS control excursions, unforeseen actuator enabling's or actions, thermal stresses, power aberrations, failure to authenticate, software or counter resets, etc. Mitigation might include additional TMONs, more detailed AGC and PLL thresholds to alert operators, auto-capturing state snapshot images in memory when unexpected conditions occur, signal spectra measurements, and expanded default diagnostic telemetry modes to help in identifying and resolving anomalous conditions.
|
|
The [spacecraft] shall integrate cyber related detection and responses with existing fault management capabilities to ensure tight integration between traditional fault management and cyber intrusion detection and prevention.{SV-DCO-1}{AU-6(4),IR-4,IR-4(1),RA-10,SA-8(21),SA-8(26),SC-3(4),SI-3,SI-3(10),SI-4(7),SI-4(13),SI-4(16),SI-4(24),SI-4(25),SI-7(7),SI-13}
|
The onboard IPS system should be integrated into the existing onboard spacecraft fault management system (FMS) because the FMS has its own fault detection and response system built in. SV corrective behavior is usually limited to automated fault responses and ground commanded recovery actions. Intrusion prevention and response methods will inform resilient cybersecurity design. These methods enable detected threat activity to trigger defensive responses and resilient SV recovery.
|
|
The [spacecraft] shall implement cryptographic mechanisms to protect the integrity of audit information and audit tools.{SV-DCO-1}{AU-9(3),RA-10,SC-8(1),SI-3,SI-3(10),SI-4(24)}
|
|
|
The [organization] shall ensure that the allocated security safeguards operate in a coordinated and mutually reinforcing manner.{SV-MA-6}{CA-7(5),PL-7,PL-8(1),SA-8(19)}
|
|
|
The [organization] shall document and design a security architecture using a defense-in-depth approach that allocates the [organization]s defined safeguards to the indicated locations and layers: [Examples include: operating system abstractions and hardware mechanisms to the separate processors in the platform, internal components, and the FSW].{SV-MA-6}{CA-9,PL-7,PL-8,PL-8(1),SA-8(3),SA-8(4),SA-8(7),SA-8(9),SA-8(11),SA-8(13),SA-8(19),SA-8(29),SA-8(30)}
|
|
|
The [spacecraft] shall prevent the installation of Flight Software without verification that the component has been digitally signed using a certificate that is recognized and approved by the ground.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-9}{CM-3,CM-3(8),CM-5,CM-5(3),CM-14,SA-8(8),SA-8(31),SA-10(2),SI-3,SI-7(12),SI-7(15)}
|
|
|
The [organization] shall employ automated tools that provide notification to ground operators upon discovering discrepancies during integrity verification.{CM-3(5),CM-6,IR-6,IR-6(2),SA-8(21),SC-51,SI-3,SI-4(7),SI-4(12),SI-4(24),SI-7(2)}
|
|
|
The [spacecraft] shall provide automatic notification to ground operators upon discovering discrepancies during integrity verification.{SV-IT-2}{CM-3(5),SA-8(21),SI-3,SI-4(7),SI-4(12),SI-4(24),SI-7(2)}
|
|
|
The [spacecraft], upon detection of a potential integrity violation, shall provide the capability to [audit the event and alert ground operators].{SV-DCO-1}{CM-3(5),SA-8(21),SI-3,SI-4(7),SI-4(12),SI-4(24),SI-7(8)}
|
One example would be for bad commands where the system would reject the command and not increment the Vehicle Command Counter (VCC) and include the information in telemetry.
|
|
The [spacecraft] shall execute procedures for ensuring that security-relevant hardware, software, and firmware updates uploaded are exactly as specified by the gold copies. {CM-3(5),SA-8(8),SA-8(21),SA-8(31),SA-10(3),SA-10(4),SA-10(6),SI-7(10),SI-7(12)}
|
|
|
The [spacecraft] shall perform an integrity check of software, firmware, and information at startup or during security-relevant events. {CM-3(5),SA-8(9),SA-8(11),SA-8(21),SI-3,SI-7(1),SI-7(10),SI-7(12),SI-7(17)}
|
|
|
The [spacecraft] shall be configured to provide only essential capabilities.{CM-6,CM-7,SA-8(2),SA-8(7),SA-8(13),SA-8(23),SA-8(26),SA-15(5)}
|
|
|
The [organization] shall ensure that software planned for reuse meets the fit, form, and function, and security as a component within the new application.{SV-SP-6,SV-SP-7,SV-SP-11}{CM-7(5)}
|
|
|
The [spacecraft] shall enter a cyber-safe mode when conditions that threaten the platform are detected, enters a cyber-safe mode of operation with restrictions as defined based on the cyber-safe mode.{SV-AV-5,SV-AV-6,SV-AV-7}{CP-10(6),CP-12,CP-13,IR-4,IR-4(1),IR-4(3),PE-10,RA-10,SA-8(16),SA-8(21),SA-8(24),SI-3,SI-4(7),SI-13,SI-17}
|
|
|
The [spacecraft] shall provide the capability to enter the platform into a known good, operational cyber-safe mode from a tamper-resistant, configuration-controlled (“gold”) image that is authenticated as coming from an acceptable supplier, and has its integrity verified.{SV-AV-5,SV-AV-6,SV-AV-7}{CP-10(6),CP-12,CP-13,IR-4(3),SA-8(16),SA-8(19),SA-8(21),SA-8(24),SI-13,SI-17}
|
Cyber-safe mode is an operating mode of a spacecraft during which all nonessential systems are shut down and the spacecraft is placed in a known good state using validated software and configuration settings. Within cyber-safe mode authentication and encryption should still be enabled. The spacecraft should be capable of reconstituting firmware and SW functions to preattack levels to allow for the recovery of functional capabilities. This can be performed by self-healing, or the healing can be aided from the ground. However, the spacecraft needs to have the capability to replan, based on available equipment still available after a cyberattack. The goal is for the vehicle to resume full mission operations. If not possible, a reduced level of mission capability should be achieved.
|
|
The [spacecraft] shall fail to a known secure state for failures during initialization, and aborts preserving information necessary to return to operations in failure.{SV-AV-5,SV-AV-6,SV-AV-7}{CP-10(6),CP-13,SA-8(16),SA-8(19),SA-8(24),SC-24,SI-13,SI-17}
|
|
|
The [organization] shall define the security safeguards that are to be automatically employed when integrity violations are discovered.{SV-IT-2}{CP-2,SA-8(21),SI-3,SI-4(7),SI-4(12),SI-7(5),SI-7(8)}
|
|
|
The [spacecraft] shall provide or support the capability for recovery and reconstitution to a known state after a disruption, compromise, or failure.{SV-AV-5,SV-AV-6,SV-AV-7}{CP-4(4),CP-10,CP-10(4),CP-10(6),CP-13,IR-4,IR-4(1),SA-8(16),SA-8(19),SA-8(24)}
|
|
|
The [spacecraft] shall be able to locate the onboard origin of a cyber attack and alert ground operators within 3 minutes.{SV-DCO-1}{IR-4,IR-4(1),IR-4(12),IR-4(13),RA-10,SA-8(22),SI-3,SI-3(10),SI-4,SI-4(1),SI-4(7),SI-4(12),SI-4(16),SI-4(24)}
|
The origin of any attack onboard the vehicle should be identifiable to support mitigation. At the very least, attacks from critical element (safety-critical or higher-attack surface) components should be locatable quickly so that timely action can occur.
|
|
The [spacecraft] shall recover to a known cyber-safe state when an anomaly is detected.{IR-4,IR-4(1),SA-8(16),SA-8(19),SA-8(21),SA-8(24),SI-3,SI-4(7),SI-10(6),SI-13,SI-17}
|
|
|
The [spacecraft] shall detect and recover from detected memory errors or transitions to a known cyber-safe state.{IR-4,IR-4(1),SA-8(16),SA-8(24),SI-3,SI-4(7),SI-10(6),SI-13,SI-17}
|
|
|
The [organization] shall implement a security architecture and design that provides the required security functionality, allocates security controls among physical and logical components, and integrates individual security functions, mechanisms, and processes together to provide required security capabilities and a unified approach to protection.{SV-MA-6}{PL-7,SA-2,SA-8,SA-8(1),SA-8(2),SA-8(3),SA-8(4),SA-8(5),SA-8(6),SA-8(7),SA-8(9),SA-8(11),SA-8(13),SA-8(19),SA-8(29),SA-8(30),SC-32,SC-32(1)}
|
|
|
The [spacecraft] shall be designed and configured so that encrypted communications traffic and data is visible to on-board security monitoring tools.{SV-DCO-1}{RA-10,SA-8(21),SI-3,SI-3(10),SI-4,SI-4(1),SI-4(10),SI-4(13),SI-4(24),SI-4(25)}
|
|
|
The [spacecraft] shall be designed and configured so that spacecraft memory can be monitored by the on-board intrusion detection/prevention capability.{SV-DCO-1}{RA-10,SA-8(21),SI-3,SI-3(10),SI-4,SI-4(1),SI-4(24),SI-16}
|
|
|
The [spacecraft] shall have on-board intrusion detection/prevention system that monitors the mission critical components or systems.{SV-AC-1,SV-AC-2,SV-MA-4}{RA-10,SC-7,SI-3,SI-3(8),SI-4,SI-4(1),SI-4(7),SI-4(13),SI-4(24),SI-4(25),SI-10(6)}
|
The mission critical components or systems could be GNC/Attitude Control, C&DH, TT&C, Fault Management.
|
|
The [spacecraft] shall generate error messages that provide information necessary for corrective actions without revealing information that could be exploited by adversaries.{SV-AV-5,SV-AV-6,SV-AV-7}{RA-5(4),SI-4(12),SI-11}
|
|
|
The [spacecraft] shall reveal error messages only to operations personnel monitoring the telemetry.{SV-AV-5,SV-AV-6,SV-AV-7}{RA-5(4),SI-4(12),SI-11}
|
|
|
The [spacecraft] shall retain the capability to update/upgrade operating systems while on-orbit.{SV-SP-7}{SA-4(5),SA-8(8),SA-8(31),SA-10(2),SI-3}
|
The operating system updates should be performed using multi-factor authorization and should only be performed when risk of compromise/exploitation of identified vulnerability outweighs the risk of not performing the update.
|
|
The [spacecraft] boot firmware must validate the boot loader, boot configuration file, and operating system image, in that order, against their respective signatures.{SV-IT-3}{SA-8(10),SA-8(11),SA-8(12),SI-7(9),SI-7(10)}
|
A signature is ~770 bits long. No requirement is imposed on the storage location of signatures.
|
|
The [spacecraft] boot firmware must verify a trust chain that extends through the hardware root of trust, boot loader, boot configuration file, and operating system image, in that order.{SV-IT-3}{SA-8(10),SA-8(11),SA-8(12),SI-7(9),SI-7(10)}
|
These three items were chosen because they’re intended to be static values (once properly set up) but are in volatile storage. Also, the Boot ROM can’t be modified, so there’s no reason to check a signature.
|
|
The [spacecraft] shall perform attestation at each stage of startup and ensure overall trusted boot regime (i.e., root of trust).{SV-IT-3}{SA-8(10),SA-8(11),SA-8(12),SI-7(9),SI-7(10),SI-7(17)}
|
It is important for the computing module to be able to access a set of functions and commands that it trusts; that is, that it knows to be true. This concept is referred to as root of trust (RoT) and should be included in the spacecraft design. With RoT, a device can always be trusted to operate as expected. RoT functions, such as verifying the device’s own code and configuration, must be implemented in secure hardware (i.e., field programmable gate arrays). By checking the security of each stage of power-up, RoT devices form the first link in a chain of trust that protects the spacecraft
|
|
The [spacecraft] shall maintain a separate execution domain for each executing process.{SV-AC-6}{SA-8(14),SA-8(19),SC-2(2),SC-7(21),SC-39,SI-3}
|
|
|
The [spacecraft] shall provide the capability to verify the correct operation of security-relevant software and hardware mechanisms (e.g.spacecraft IDS/IPS, logging, crypto, etc..) {SV-DCO-1}{SA-8(21),SI-3,SI-6}
|
|
|
The [spacecraft] software subsystems shall provide independent mission/cyber critical threads such that any one credible event will not corrupt another mission/cyber critical thread.{SV-MA-3,SV-AV-7}{SC-3}
|
|
|
The [spacecraft] shall provide independent mission/cyber critical threads such that any one credible event will not corrupt another mission/cyber critical thread.{SC-3,SC-32,SC-32(1),SI-3,SI-13}
|
|
|
The [spacecraft] software subsystems shall accept [Program defined hazardous] commands only when prerequisite checks are satisfied.{SV-MA-3,SV-AV-7}{SI-10}
|
|
|
The [spacecraft] software subsystems shall identify and reject commands received out-of-sequence when the out-of-sequence commands can cause a hazard/failure or degrade the control of a hazard or mission.{SV-MA-3,SV-AV-7}{SI-10}
|
|
|
The [spacecraft] software subsystems shall perform prerequisite checks for the execution of hazardous commands.{SV-MA-3,SV-AV-7}{SI-10}
|
|
|
The [spacecraft] software subsystems shall discriminate between valid and invalid input into the software and rejects invalid input.{SV-MA-3,SV-AV-7}{SI-10,SI-10(3)}
|
|
|
The [spacecraft] software subsystems shall properly handle spurious input and missing data.{SV-MA-3,SV-AV-7}{SI-10,SI-10(3)}
|
|
|
The [spacecraft] software subsystems shall validate a functionally independent parameter prior to the issuance of any sequence that could remove an inhibit or perform a hazardous action.{SV-MA-3,SV-AV-7}{SI-10(3)}
|
|
|
The [spacecraft] mission/cyber critical commands shall be "complex" and/or diverse from other commands so that a single bit flip could not transform a benign command into a hazardous command.{SV-MA-3,SV-AV-7}{SI-10(5)}
|
|
|
The [spacecraft] software subsystems shall provide at least one independent command for each operator-initiated action used to shut down a function leading to or reducing the control of a hazard.{SV-MA-3,SV-AV-7}{SI-10(5)}
|
|
|
The [spacecraft] shall have failure tolerance on sensors used by software to make mission-critical decisions.{SV-MA-3,SV-AV-7}{SI-13,SI-17}
|
|
|
The [spacecraft] cyber-safe mode software/configuration should be stored onboard the spacecraft in memory with hardware-based controls and should not be modifiable.{SV-AV-5,SV-AV-6,SV-AV-7}{SI-17}
|
Cyber-safe mode is using a fail-secure mentality where if there is a malfunction that the spacecraft goes into a fail-secure state where cyber protections like authentication and encryption are still employed (instead of bypassed) and the spacecraft can be restored by authorized commands. The cyber-safe mode should be stored in a high integrity location of the on-board SV so that it cannot be modified by attackers.
|
|
The [spacecraft] software subsystems shall detect and recover/transition from detected memory errors to a known cyber-safe state.{SV-MA-3,SV-AV-7}{SI-17}
|
|
|
The [spacecraft] software subsystems shall initialize the spacecraft to a known safe state.{SV-MA-3,SV-AV-7}{SI-17}
|
|
|
The [spacecraft] software subsystems shall operate securely in off-nominal power conditions, including loss of power and spurious power transients.{SV-MA-3,SV-AV-7}{SI-17}
|
|
|
The [spacecraft] software subsystems shall perform an orderly, controlled system shutdown to a known cyber-safe state upon receipt of a termination command or condition.{SV-MA-3,SV-AV-7}{SI-17}
|
|
|
The [spacecraft] software subsystems shall recover to a known cyber-safe state when an anomaly is detected.{SV-MA-3,SV-AV-7}{SI-17}
|
|
|
The [spacecraft] software subsystems shall safely transition between all predefined, known states.{SV-MA-3,SV-AV-7}{SI-17}
|
|
|
The [spacecraft] hardware root of trust must be an ECDSA NIST P-384 public key.{SV-IT-3}{SI-7(9)}
|
No requirement is imposed on uniqueness.
|
|
The [spacecraft] hardware root of trust must be loadable only once, post-purchase.{SV-IT-3}{SI-7(9)}
|
No requirement is imposed on preventing hardware readout. The public key belongs to the customer, not the manufacturer, so it must be loaded after purchase. Also, if it can be overwritten, there’s no reason to trust it.
|
|
The [spacecraft] shall implement trusted boot/RoT as a separate compute engine controlling the trusted computing platform cryptographic processor.{SV-IT-3}{SI-7(9)}
|
|
|
The [spacecraft] shall implement trusted boot/RoT computing module on radiation tolerant burn-in (non-programmable) equipment.{SV-IT-3}{SI-7(9)}
|
|
|
The [spacecraft] boot firmware must enter a recovery routine upon failing to verify signed data in the trust chain, and not execute or trust that signed data.{SV-IT-3}{SI-7(9),SI-7(10)}
|
No other requirements are imposed on the recovery routine besides not using the failed data. Unverifiable data isn’t trusted and shouldn’t be run.
|
|
The [spacecraft] secure boot mechanism shall be Commercial National Security Algorithm Suite (CNSA) compliant.{SV-IT-3}{SI-7(9),SI-7(10)}
|
No certification process is required (or exists). The CNSA is easy to meet, only restricts algorithm choice, and aids ease-of-use for government customers.
|
|
The [spacecraft] shall allocate enough boot ROM memory for secure boot firmware execution.{SV-IT-3}{SI-7(9),SI-7(10)}
|
|
|
The [spacecraft] shall allocate enough SRAM memory for secure boot firmware execution.{SV-IT-3}{SI-7(9),SI-7(10)}
|
|
|
The [spacecraft] shall support the algorithmic construct of Elliptic Curve Digital Signature Algorithm (ECDSA) NIST P-384 + SHA-38 or equivalent strength.{SV-IT-3}{SI-7(9),SI-7(10)}
|
Timing data may suggest cryptographic accelerators are unnecessary. This construct was chosen because (a) it’s in the CNSA suite and (b) it doesn’t require secret values to be stored
|
|
The [spacecraft] shall utilize strong fault management and redundancy to help mitigate threats against TT&C failure.{SV-AV-7}
|
|