|
The [organization] shall identify the applicable physical and environmental protection policies covering the development environment and spacecraft hardware. {PE-1,PE-14,SA-3,SA-3(1),SA-10(3)}
|
|
|
The [organization] shall analyze changes to the spacecraft to determine potential security impacts prior to change implementation.{CM-4,CM-3,CM-3(2),CM-3(7),CM-4(2),SA-10}
|
|
|
The [organization] shall develop and document an inventory of the spacecraft components that accurately reflects the to-be launched system. {CM-8,CM-2}
|
|
|
The [organization] updates the inventory of spacecraft components as an integral part of component installations, removals, and spacecraft updates.{CM-8(1),CA-7,CM-2,CM-3}
|
|
|
The [organization] shall develop and document program-specific identification and authentication policies for accessing the development environment and spacecraft. {AC-3,AC-14,IA-1,SA-3,SA-3(1)}
|
|
|
The [organization] shall protect documentation and Controlled Unclassified Information (CUI) as required, in accordance with the risk management strategy.{AC-3,CM-12,CP-2,PM-17,RA-5(4),SA-3,SA-3(1),SA-5,SA-10,SC-8(1),SC-28(3),SI-12}
|
|
|
The [organization] shall identify and properly classify mission sensitive design/operations information and access control shall be applied in accordance with classification guides and applicable federal laws, Executive Orders, directives, policies, regulations, and standards.{SV-CF-3,SV-AV-5}{AC-3,CM-12,CP-2,PM-17,RA-5(4),SA-3,SA-3(1),SA-5,SA-8(19),SC-8(1),SC-28(3),SI-12}
|
* Mission sensitive information should be classified as Controlled Unclassified Information (CUI) or formally known as Sensitive but Unclassified. Ideally these artifacts would be rated SECRET or higher and stored on classified networks. Mission sensitive information can typically include a wide range of candidate material: the functional and performance specifications, the RF ICDs, databases, scripts, simulation and rehearsal results/reports, descriptions of uplink protection including any disabling/bypass features, failure/anomaly resolution, and any other sensitive information related to architecture, software, and flight/ground /mission operations. This could all need protection at the appropriate level (e.g., unclassified, SBU, classified, etc.) to mitigate levels of cyber intrusions that may be conducted against the project’s networks. Stand-alone systems and/or separate database encryption may be needed with controlled access and on-going Configuration Management to ensure changes in command procedures and critical database areas are tracked, controlled, and fully tested to avoid loss of science or the entire mission.
|
|
The [organization] shall ensure security requirements/configurations are placed in accordance with NIST 800-171 with enhancements in 800-172 on the development environments to prevent the compromise of source code from supply chain or information leakage perspective.{AC-3,SA-3,SA-3(1),SA-15}
|
|
|
The [organization] shall identify the key system components or capabilities that require isolation through physical or logical means.{SV-AC-6}{AC-3,SC-3,SC-7(13),SC-28(3),SC-32,SC-32(1)}
|
Fault management and security management capabilities would be classified as mission critical and likely need separated. Additionally, capabilities like TT&C, C&DH, GNC might need separated as well.
|
|
The [organization] shall ensure any update to on-board software, memory, or stored procedures has met high assurance standards before execution. {AC-3(2),CM-3,SA-8(8),SA-8(31),SA-10(2),SR-4(4)}
|
|
|
The [organization] shall ensure that role-based security-related training is provided to personnel with assigned security roles and responsibilities: (i) before authorizing access to the system or performing assigned duties; (ii) when required by system changes; and (iii) at least annually thereafter.{AT-3,CP-2}
|
|
|
The [organization] shall provide training to its personnel on how to identify and respond to malicious code indicators to include but not limited to indicators of potentially malicious code in flight software, indicators from development machine’s anti-virus/anti-malware software of potential malicious code, and to recognize suspicious communications and anomalous behavior in [organization] information systems.{AT-3(4),IR-6,IR-6(2),SI-4(24)}
|
|
|
The [organization] shall engage relevant stakeholders to discuss performance impacts/tradeoffs for implementing the desired monitoring approach, document any deviations from initial desired approach, and ensure the Authorizing Official (AO) signs off on the risk posed by the exclusion of the functionality in question.{AU-2}
|
Aerospace work published in TOR-2019-02178 "Telemetry Security" provides examples of telemetry values that may be useful to monitor for indications of malicious onboard activity (not a comprehensive list):
Vehicle Command Counter (VCC)
Rejected Command Counter
Command Receiver On/Off Mode
Command Receivers Received Signal Strength
Command Receiver Lock Modes
Telemetry Downlink Modes
Cryptographic Modes
Received Commands
System Clock
GPS Ephemeris
Watchdog Timer (WDT)
|
|
The [organization] shall identify and document the on-board events and values that will be monitored for indicators of unexpected or malicious activity.{AU-2}
|
Aerospace work published in TOR-2019-02178 "Telemetry Security" provides examples of telemetry values that may be useful to monitor for indications of malicious onboard activity (not a comprehensive list):
Vehicle Command Counter (VCC)
Rejected Command Counter
Command Receiver On/Off Mode
Command Receivers Received Signal Strength
Command Receiver Lock Modes
Telemetry Downlink Modes
Cryptographic Modes
Received Commands
System Clock
GPS Ephemeris
Watchdog Timer (WDT)
|
|
The [organization] shall employ independent third-party analysis and penetration testing of all software (COTS, FOSS, Custom) associated with the system, system components, or system services.{CA-2,CA-2(1),CA-8(1),CM-10(1),SA-9,SA-11(3),SA-12(11),SI-3,SI-3(10),SR-4(4),SR-6(1)}
|
|
|
In coordination with [organization], the [organization] shall prioritize and remediate flaws identified during security testing/evaluation.{CA-2,CA-5,SA-11,SI-3,SI-3(10)}
|
|
|
The [organization] shall implement a verifiable flaw remediation process into the developmental and operational configuration management process.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CA-2,CA-5,SA-3,SA-3(1),SA-11,SI-3,SI-3(10)}
|
The verifiable process should also include a cross reference to mission objectives and impact statements. Understanding the flaws discovered and how they correlate to mission objectives will aid in prioritization.
|
|
The [organization] shall maintain evidence of the execution of the security assessment plan and the results of the security testing/evaluation.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CA-2,CA-8,SA-11}
|
|
|
The [organization] shall create and implement a security assessment plan that includes: (1) The types of analyses, testing, evaluation, and reviews of all software and firmware components; (2) The degree of rigor to be applied to include abuse cases and/or penetration testing; and (3) The types of artifacts produced during those processes.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CA-2,CA-8,SA-11,SA-11(5)}
|
The security assessment plan should include evaluation of mission objectives in relation to the security of the mission. Assessments should not only be control based but also functional based to ensure mission is resilient against failures of controls.
|
|
The [organization] shall determine the vulnerabilities/weaknesses that require remediation, and coordinate the timeline for that remediation, in accordance with the analysis of the vulnerability scan report, the mission assessment of risk, and mission needs.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CA-5,CM-3,RA-5,RA-7,SI-3,SI-3(10)}
|
|
|
The [organization] shall implement automated mechanisms to assist in the execution and implementation of the Continuous Monitoring Program (CMP).{CA-7(6)}
|
|
|
The [organization] shall coordinate penetration testing on mission critical spacecraft components (hardware and/or software).{SV-MA-4}{CA-8,CA-8(1),CP-4(5)}
|
Not all defects (i.e., buffer overflows, race conditions, and memory leaks) can be discovered statically and require execution of the system. This is where space-centric cyber testbeds (i.e., cyber ranges) are imperative as they provide an environment to maliciously attack components in a controlled environment to discover these undesirable conditions. Technology has improved to where digital twins for spacecraft are achievable, which provides an avenue for cyber testing that was often not performed due to perceived risk to the flight hardware.
|
|
The [organization] shall employ dynamic analysis (e.g.using simulation, penetration testing, fuzzing, etc.) to identify software/firmware weaknesses and vulnerabilities in developed and incorporated code (open source, commercial, or third-party developed code).{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CA-8,CM-10(1),RA-3(1),SA-11(5),SA-11(8),SA-11(9),SI-3,SI-7(10)}
|
|
|
The [organization] shall establish robust procedures and technical methods to perform testing to include adversarial testing (i.e.abuse cases) of the platform hardware and software.{CA-8,CP-4(5),RA-5,RA-5(1),RA-5(2),SA-3,SA-4(3),SA-11,SA-11(1),SA-11(2),SA-11(5),SA-11(7),SA-11(8),SA-15(7)}
|
|
|
The [organization] shall perform penetration testing/analysis: (1) On potential system elements before accepting the system; (2) As a realistic simulation of the active adversary’s known adversary tactics, techniques, procedures (TTPs), and tools; and (3) Throughout the lifecycle on physical and logical systems, elements, and processes.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{CA-8(1),SA-9,SA-11(5),SR-5(2)}
|
Penetration testing should be performed throughout the lifecycle on physical and logical systems, elements, and processes including: (1) Hardware, software, and firmware development processes; (2) Shipping/handling procedures; (3) Personnel and physical security programs; (4) Configuration management tools/measures to maintain provenance; and (5) Any other programs, processes, or procedures associated with the production/distribution of supply chain elements.
|
|
The [organization] shall develop and document program-specific configuration management policies and procedures for the hardware and software for the spacecraft. {CM-1,CM-3,CM-5(6),SA-10,SA-10(3)}
|
|
|
The [organization] shall track security advisories, patches/updates, and ensure compliance with license agreements and usage restrictions for all software within the SBOM.{CM-10}
|
|
|
The [organization] shall perform software component analysis (a.k.a.origin analysis) for developed or acquired software.{CM-10,CM-10(1),RA-3(1),RA-5,SA-15(7),SI-3,SI-3(10),SR-4(4)}
|
|
|
The [organization] shall maintain a list of suppliers and potential suppliers used, and the products that they supply to include software.{SV-SP-3,SV-SP-4,SV-SP-11}{CM-10,PL-8(2),PM-30,SA-8(9),SA-8(11)}
|
Ideally you have diversification with suppliers
|
|
The [organization] shall distribute documentation to only personnel with defined roles and a need to know.{SV-CF-3,SV-AV-5}{CM-12,CP-2,SA-5,SA-10}
|
Least privilege and need to know should be employed with the protection of all documentation. Documentation can contain sensitive information that can aid in vulnerability discovery, detection, and exploitation. For example, command dictionaries for ground and space systems should be handles with extreme care. Additionally, design documents for missions contain many key elements that if compromised could aid in an attacker successfully exploiting the system.
|
|
The [organization] shall confirm that the operational spacecrafts correspond to the baseline configuration. {CM-2,CM-3,CM-3(7),CM-4(2),CM-6,SA-10}
|
|
|
The [organization] shall develop, document, and maintain under configuration control, a current baseline configuration of the spacecrafts.{CM-2,CM-3(7),CM-4(2),CM-6,SA-8(30),SA-10}
|
|
|
The [organization] shall establish and formally review the baseline configuration to confirm that it represents an agreed-upon set of specifications for the spacecrafts.{CM-2,CM-6}
|
|
|
The [organization] shall retain at least two previous versions of all spacecraft associated software on the ground with the capability to restore previous version on the spacecraft.{CM-2(3),CM-3(7),CM-4(2),SA-10,SA-10(4)}
|
|
|
The [organization] shall test software and firmware updates related to flaw remediation for effectiveness and potential side effects on mission systems in a separate test environment before installation.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CM-3,CM-3(1),CM-3(2),CM-4(1),CM-4(2),CM-10(1),SA-8(31),SA-11(9),SI-2,SI-3,SI-3(10),SI-7(10),SI-7(12),SR-5(2)}
|
This requirement is focused on software and firmware flaws. If hardware flaw remediation is required, refine the requirement to make this clear.
|
|
The [organization] shall define processes and procedures to be followed when integrity verification tools detect unauthorized changes to software, firmware, and information.{SV-IT-2}{CM-3,CM-3(1),CM-3(5),CM-5(6),CM-6,CP-2,IR-6,IR-6(2),PM-30,SC-16(1),SC-51,SI-3,SI-4(7),SI-4(24),SI-7,SI-7(7),SI-7(10)}
|
|
|
The [organization] shall release updated versions of the mission information systems incorporating security-relevant software and firmware updates, after suitable regression testing, at a frequency no greater than [Program-defined frequency [90 days]].{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CM-3(2),CM-4(1)}
|
On-orbit patching/upgrades may be necessary if vulnerabilities are discovered after launch. The system should have the ability to update software post-launch.
|
|
The [organization] shall ensure security representatives are included in all change control board reviews and decisions.{CM-3(4),SA-10(7)}
|
|
|
The [organization] shall ensure that cryptographic mechanisms, including authentication schemes and command dictionaries, are under strict configuration management.{CM-3(6)}
|
|
|
The [organization] shall implement a two-person rule, or similar dual authorization mechanism, for all changes to the SV configuration, and such actions should only be conducted with documented change control board approval.{CM-3(8)}
|
|
|
The [organization] shall develop and implement anti-counterfeit policy and procedures designed to detect and prevent counterfeit components from entering the information system, including support tamper resistance and provide a level of protection against the introduction of malicious code or hardware.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{CM-3(8),CM-7(9),PM-30,SA-8(9),SA-8(11),SA-9,SA-10(3),SA-19,SC-51,SR-4(3),SR-4(4),SR-5(2),SR-11}
|
|
|
The [organization] shall define, document, and approve access restrictions associated with changes to the spacecraft.{CM-5}
|
|
|
The [organization] shall develop and document spacecraft integrity policies covering both hardware and software. {CM-5(6),SA-10(3),SI-1,SI-7(12)}
|
|
|
The [organization] shall maintain the integrity of the mapping between the master build data (hardware drawings and software/firmware code) describing the current version of hardware, software, and firmware and the on-site master copy of the data for the current version.{CM-6,SA-8(21),SA-8(30),SA-10,SA-10(3),SA-10(4),SA-10(5),SI-7(10),SR-4(4)}
|
|
|
The [organization] shall define/maintain an approved operating system list for use on spacecraft.{SV-SP-7}{CM-7(5)}
|
The operating system is extremely important to security and availability of the spacecraft, therefore should receive high levels of assurance that it operates as intended and free of critical weaknesses/vulnerabilities.
|
|
The [organization] shall prohibit the use of binary or machine-executable code from sources with limited or no warranty and without the provision of source code.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CM-7(8)}
|
|
|
The [organization] prohibits the use of binary or machine-executable code from sources with limited or no warranty and without the provision of source code.{CM-7(8),CM-7(8),CM-10(1),SA-8(9),SA-8(11),SA-10(2),SI-3,SR-4(4)}
|
|
|
The [organization] shall maintain a Software Bill of Materials (SBOM) for all software code utilized and continuously update/revise the SBOM for each step in the software lifecycle (to include the deployment of that software).{CM-8}
|
|
|
The [organization] shall conduct a criticality analysis to identify mission critical functions and critical components and reduce the vulnerability of such functions and components through secure system design.{SV-SP-3,SV-SP-4,SV-AV-7,SV-MA-4}{CP-2,CP-2(8),PL-7,PM-11,PM-30(1),RA-3(1),RA-9,SA-8(9),SA-8(11),SA-8(25),SA-12,SA-14,SA-15(3),SC-7(29),SR-1}
|
During SCRM, criticality analysis will aid in determining supply chain risk. For mission critical functions/components, extra scrutiny must be applied to ensure supply chain is secured.
|
|
The [organization] shall develop an incident response and forensics plan that covers the spacecrafts.{CP-2,IR-1,IR-3,IR-3(2),IR-4(12),IR-4(13),IR-8,SA-15(10),SI-4(24)}
|
|
|
The [organization] shall employ techniques to limit harm from potential adversaries identifying and targeting the [organization]s supply chain.{CP-2,PM-30,SA-9,SA-12(5),SC-38,SR-3,SR-3(1),SR-3(2),SR-5(2)}
|
|
|
The [organization] defines the security safeguards to be employed to protect the availability of system resources.{CP-2(2),SC-6,SI-13,SI-17}
|
|
|
The [organization] shall employ Operations Security (OPSEC) safeguards to protect supply chain-related information for the system, system components, or system services. {CP-2(8),PM-30,SA-12(9),SC-38,SR-7}
|
|
|
The [organization] shall test the incident response capabilities of the spacecraft to determine the effectiveness of the plan and readiness to execute the plan.{IR-3}
|
|
|
The [organization] shall coordinate testing of the incident response plan with organizational elements responsible for related plans.{IR-3(2)}
|
|
|
The [organization] shall report counterfeit information system components to [organization] officials. {SV-SP-4}{IR-6,IR-6(2),PM-30,SA-19,SR-11}
|
|
|
The [organization] shall report identified systems or system components containing software affected by recently announced cybersecurity-related software flaws (and potential vulnerabilities resulting from those flaws) to [organization] officials with cybersecurity responsibilities.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-11}{IR-6,IR-6(2),SI-2,SI-3,SI-4(12),SR-4(4)}
|
|
|
The [organization] shall develop a security plan for the spacecraft.{SV-MA-6}{PL-2,PL-7,PM-1,SA-8(29),SA-8(30)}
|
|
|
The [organization] shall define the secure communication protocols to be used within the mission in accordance with applicable federal laws, Executive Orders, directives, policies, regulations, and standards.{PL-7,RA-5(4),SA-4(9),SA-8(18),SA-8(19),SC-8(1),SC-16(3),SC-40(4),SI-12}
|
|
|
The [organization] shall document the platform's security architecture, and how it is established within and is an integrated part of the overall [organization] mission security architecture.{PL-7,SA-8(7),SA-8(13),SA-8(29),SA-8(30),SA-17}
|
|
|
The [organization] shall use all-source intelligence analysis of suppliers and potential suppliers of the information system, system components, or system services to inform engineering, acquisition, and risk management decisions.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{PM-16,PM-30,RA-2,RA-3(1),RA-3(2),RA-7,SA-9,SA-12(8),SR-5(2)}
|
* The Program should also consider sub suppliers and potential sub suppliers.
* All-source intelligence of suppliers that the organization may use includes: (1) Defense Intelligence Agency (DIA) Threat Assessment Center (TAC), the enterprise focal point for supplier threat assessments for the DOD acquisition community risks; (2) Other U.S. Government resources including: (a) Government Industry Data Exchange Program (GIDEP) – Database where government and industry can record issues with suppliers, including counterfeits; and (b) System for Award Management (SAM) – Database of companies that are barred from doing business with the US Government.
|
|
The [organization] shall request threat analysis of suppliers of critical components and manage access to and control of threat analysis products containing U.S.person information.{SV-SP-3,SV-SP-4,SV-SP-11}{PM-16,PM-30(1),RA-3(1),SA-9,SA-12,SR-1}
|
The intent of this requirement is to address supply chain concerns on hardware and software vendors. Not required for trusted suppliers accredited to the Defense Microelectronic Activity (DMEA). If the Program intends to use a supplier not accredited by DMEA, the government customer should be notified as soon as possible. If the Program has internal processes to vet suppliers, it may meet this requirement. All software used and its origins must be included in the SBOM and be subjected to internal and Government vulnerability scans.
|
|
The [organization] shall conduct a supplier review prior to entering into a contractual agreement with a sub [organization] to acquire systems, system components, or system services.{PM-30,PM-30(1),RA-3(1),SA-8(9),SA-8(11),SA-9,SA-12(2),SR-5(2),SR-6}
|
|
|
The [organization] shall maintain documentation tracing the strategies, tools, and methods implemented to mitigate supply chain risk .{SV-SP-3,SV-SP-4,SV-AV-7}{PM-30,RA-3(1),SA-12(1),SR-5}
|
Examples include: (1) Transferring a portion of the risk to the developer or supplier through the use of contract language and incentives; (2) Using contract language that requires the implementation of SCRM throughout the system lifecycle in applicable contracts and other acquisition and assistance instruments (grants, cooperative agreements, Cooperative Research and Development Agreements (CRADAs), and other transactions). Within the DOD some examples include: (a) Language outlined in the Defense Acquisition Guidebook section 13.13. Contracting; (b) Language requiring the use of protected mechanisms to deliver elements and data about elements, processes, and delivery mechanisms; (c) Language that articulates that requirements flow down supply chain tiers to sub-prime suppliers. (3) Incentives for suppliers that: (a) Implement required security safeguards and SCRM best practices; (b) Promote transparency into their organizational processes and security practices; (c) Provide additional vetting of the processes and security practices of subordinate suppliers, critical information system components, and services; and (d) Implement contract to reduce SC risk down the contract stack. (4) Gaining insight into supplier security practices; (5) Using contract language and incentives to enable more robust risk management later in the lifecycle; (6) Using a centralized intermediary or “Blind Buy” approaches to acquire element(s) to hide actual usage locations from an untrustworthy supplier or adversary;
|
|
The [organization] shall protect against supply chain threats to the system, system components, or system services by employing security safeguards as defined by NIST SP 800-161 Rev.1.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{PM-30,RA-3(1),SA-8(9),SA-8(11),SA-12,SI-3,SR-1}
|
The chosen supply chain safeguards should demonstrably support a comprehensive, defense-in-breadth information security strategy. Safeguards should include protections for both hardware and software. Program should define their critical components (HW & SW) and identify the supply chain protections, approach/posture/process.
|
|
The [organization] shall use the threat and vulnerability analyses of the as-built system, system components, or system services to inform and direct subsequent testing/evaluation of the as-built system, component, or service.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{RA-3(3),SA-11(2),SA-15(8),SI-3}
|
|
|
The [organization] shall share information obtained from the vulnerability scanning process and security control assessments with [Program-defined personnel or roles] to help eliminate similar vulnerabilities in other systems (i.e., systemic weaknesses or deficiencies).{SV-SP-1}{RA-5}
|
|
|
The [organization] shall ensure that the vulnerability scanning tools (e.g., static analysis and/or component analysis tools) used include the capability to readily update the list of potential information system vulnerabilities to be scanned.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{RA-5,RA-5(1),RA-5(3),SI-3}
|
|
|
The [organization] shall perform vulnerability analysis and risk assessment of all systems and software.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{RA-5,RA-5(3),SA-15(7),SI-3}
|
|
|
The [organization] shall ensure that vulnerability scanning tools and techniques are employed that facilitate interoperability among tools and automate parts of the vulnerability management process by using standards for: (1) Enumerating platforms, custom software flaws, and improper configurations; (2) Formatting checklists and test procedures; and (3) Measuring vulnerability impact.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{RA-5,RA-5(3),SI-3}
|
Component/Origin scanning looks for open-source libraries/software that may be included into the baseline and looks for known vulnerabilities and open-source license violations.
|
|
The [organization] shall perform static binary analysis of all firmware that is utilized on the spacecraft.{SV-SP-7,SV-SP-11}{RA-5,SA-10,SA-11,SI-7(10)}
|
Many commercial products/parts are utilized within the system and should be analyzed for security weaknesses. Blindly accepting the firmware is free of weakness is unacceptable for high assurance missions. The intent is to not blindly accept firmware from unknown sources and assume it is secure. This is meant to apply to firmware the vendors are not developing internally. In-house developed firmware should be going through the vendor's own testing program and have high assurance it is secure. When utilizing firmware from other sources, "expecting" does not meet this requirement. Each supplier needs to provide evidence to support that claim that their firmware they are getting is genuine and secure.
|
|
The [organization] shall perform static source code analysis for all available source code looking for [[organization]-defined Top CWE List] weaknesses using complimentary set of static code analysis tools (i.e.more than one).{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{RA-5,SA-11(1),SA-15(7)}
|
|
|
The [organization] shall analyze vulnerability/weakness scan reports and results from security control assessments.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{RA-5,SI-3}
|
|
|
The [organization] shall ensure that the list of potential system vulnerabilities scanned is updated [prior to a new scan] {SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{RA-5(2),SI-3}
|
|
|
The [organization] shall perform configuration management during system, component, or service during [design; development; implementation; operations].{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-10}
|
|
|
The [organization] shall review proposed changes to the spacecraft, assessing both mission and security impacts.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-10,CM-3(2)}
|
|
|
The [organization] shall correct flaws identified during security testing/evaluation.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-11}
|
Flaws that impact the mission objectives should be prioritized.
|
|
The [organization] shall perform [Selection (one or more): unit; integration; system; regression] testing/evaluation at [Program-defined depth and coverage].{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-11}
|
The depth needs to include functional testing as well as negative/abuse testing.
|
|
The [organization] shall perform and document threat and vulnerability analyses of the as-built system, system components, or system services.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-11(2),SI-3}
|
|
|
The [organization] shall perform manual code review of all produced code looking for quality, maintainability, and security flaws.{SA-11(4),SI-3,SI-3(10),SR-4(4)}
|
|
|
The [organization] shall have automated means to evaluate adherence to coding standards.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-15,SA-15(7),RA-5}
|
Manual review cannot scale across the code base; you must have a way to scale in order to confirm your coding standards are being met. The intent is for automated means to ensure code adheres to a coding standard.
|
|
The [organization] shall perform component analysis (a.k.a.origin analysis) for developed or acquired software.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-15(7),RA-5}
|
|
|
The [organization] shall document the spacecraft's security architecture, and how it is established within and is an integrated part of the Program's mission security architecture.{SV-MA-6}{SA-17}
|
|
|
The [organization] shall require subcontractors developing information system components or providing information system services (as appropriate) to demonstrate the use of a system development life cycle that includes [state-of-the-practice system/security engineering methods, software development methods, testing/evaluation/validation techniques, and quality control processes].{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-9}{SA-3,SA-4(3)}
|
Select the particular subcontractors, software vendors, and manufacturers based on the criticality analysis performed for the Program Protection Plan and the criticality of the components that they supply.
|
|
The [organization] shall require the developer of the system, system component, or system service to deliver the system, component, or service with [Program-defined security configurations] implemented.{SV-SP-1,SV-SP-9}{SA-4(5)}
|
For the spacecraft FSW, the defined security configuration could include to ensure the software does not contain a pre-defined list of Common Weakness Enumerations (CWEs)and/or CAT I/II Application STIGs.
|
|
The [organization] shall ensure that all Electrical, Electronic, Electro-mechanical & Electro-optical (EEEE) and mechanical piece parts procured from the Original Component Manufacturer (OCM) or their authorized distribution network.{SA-8(9),SA-8(11),SA-12,SA-12(1),SC-16(1),SR-1,SR-5}
|
|
|
The [organization] shall use a certified environment to develop, code and test executable software (firmware or bit-stream) that will be programmed into a one-time programmable FPGA or be programmed into non-volatile memory (NVRAM) that the FPGA executes.{SA-8(9),SA-8(11),SA-12,SA-12(1),SC-51,SI-7(10),SR-1,SR-5}
|
|
|
The [organization] shall ensure that all ASICs designed, developed, manufactured, packaged, and tested by suppliers with a Defense Microelectronics Activity (DMEA) Trust accreditation.{spacecraft-SP-5} {SA-8(9),SA-8(11),SA-12,SA-12(1),SR-1,SR-5}
|
|
|
The [organization] shall correct reported cybersecurity-related information system flaws.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SI-2}
|
* Although this requirement is stated to specifically apply to cybersecurity-related flaws, the Program office may choose to broaden it to all SV flaws.
* This requirement is allocated to the Program, as it is presumed, they have the greatest knowledge of the components of the system and when identified flaws apply.
|
|
The [organization] shall identify, report, and coordinate correction of cybersecurity-related information system flaws.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SI-2}
|
|
|
The [organization] shall determine criteria for unusual or unauthorized activities or conditions for all communications to/from the spacecraft.{SI-4(4)}
|
|
|
If using the Government Microelectronics Assessment for Trust (GOMAT) framework outright, to perform ASIC and FPGA threat/vulnerability risk assessment, the following requirements would apply: {SV-SP-5}{SR-1,SR-5}
|
• 1.g “In coordination with the DOD CIO, the Director, Defense Intelligence Agency (DIA), and the Heads of the DOD Components, develop a strategy for managing risk in the supply chain for integrated circuit-related products and services (e.g., FPGAs, printed circuit boards) that are identifiable to the supplier as specifically created or modified for DOD (e.g., military temperature range, radiation hardened).
|
|
The [organization] shall inspect system components periodically during development to detect tampering (in accordance with the Anti-Tamper Plan).{SR-10}
|
|
|
The [organization] shall develop and implement anti-counterfeit policy and procedures, in coordination with the [CIO], that is demonstrably consistent with the anti-counterfeit policy defined by the Program office.{SV-SP-4,SV-SP-11}{SR-11}
|
|
|
The [organization] shall employ technical means to determine if system components are genuine or have been altered.{SR-11(3)}
|
Organizations may leverage supplier and contractor processes for validating that a system or component is genuine and has not been altered and for replacing a suspect system or component.
|
|
The [organization] shall develop a plan for managing supply chain risks associated with the research and development, design, manufacturing, acquisition, delivery, integration, operations and maintenance, and disposal of organization-defined systems, system components, or system services.{SR-2}
|
|
|
The [organization] shall protect the supply chain risk management plan from unauthorized disclosure and modification.{SR-2}
|
|
|
The [organization] shall review and update the supply chain risk management plan as required, to address threats, organizational, or environmental changes.{SR-2}
|
|
|
The [organization] shall establish a supply chain risk management team to lead and support supply chain risk management activities.{SR-2(1)}
|
|
|
The [organization] shall ensure that the controls included in prime contracts are also included in the contracts of subcontractors.{SR-3(3)}
|
|
|
The [organization] shall document, monitor, and maintain valid provenance of critical system components and associated data in accordance with the Supply Chain Risk Management Plan.{SR-4,SR-4(1),SR-4(2)}
|
|
|
The [organization] shall employ the [organization]-defined approaches for the purchase of the system, system components, or system services from suppliers.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{SR-5}
|
This could include tailored acquisition strategies, contract tools, and procurement methods.
|
|
The [organization] shall ensure adequate supplies of critical system components.{SR-5(1)}
|
Examples include: using multiple suppliers throughout the supply chain for critical components, stockpiling spare components to ensure operation during mission-critical times, and the identification of functionally identical or similar components that may be used, if necessary.
|
|
The [organization] (and Prime Contractor) shall conduct a supplier review prior to entering into a contractual agreement with a contractor (or sub-contractor) to acquire systems, system components, or system services.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{SR-6}
|
|
|
The [organization] shall employ [Selection (one or more): independent third-party analysis, Program penetration testing, independent third-party penetration testing] of [Program-defined supply chain elements, processes, and actors] associated with the system, system components, or system services.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{SR-6(1)}
|
|
|
The [organization] shall develop an Anti-Tamper Plan in accordance with DoD directives/instructions on Anti-Tamper guidance for the system, system component, or system service.{SR-9}
|
|
|
The [organization] shall coordinate the Anti-Tamper Plan with the appropriate organizational entities to ensure correct implementation of tamper protection mechanisms throughout the system lifecycle.{SR-9,SR-9(1)}
|
|
|
The [organization] shall enable integrity verification of hardware components.{SA-10(3),SA-8(21),SA-10(3),SC-51}
|
* The integrity verification mechanisms may include:
** Stipulating and monitoring logical delivery of products and services, requiring downloading from approved, verification-enhanced sites;
** Encrypting elements (software, software patches, etc.) and supply chain process data in transit (motion) and at rest throughout delivery;
** Requiring suppliers to provide their elements “secure by default”, so that additional configuration is required to make the element insecure;
** Implementing software designs using programming languages and tools that reduce the likelihood of weaknesses;
** Implementing cryptographic hash verification; and
** Establishing performance and sub-element baseline for the system and system elements to help detect unauthorized tampering/modification during repairs/refurbishing.
** Stipulating and monitoring logical delivery of products and services, requiring downloading from approved, verification-enhanced sites;
** Encrypting elements (software, software patches, etc.) and supply chain process data in transit (motion) and at rest throughout delivery;
** Requiring suppliers to provide their elements “secure by default”, so that additional configuration is required to make the element insecure;
** Implementing software designs using programming languages and tools that reduce the likelihood of weaknesses;
** Implementing cryptographic hash verification; and
** Establishing performance and sub-element baseline for the system and system elements to help detect unauthorized tampering/modification during repairs/refurbishing.
|
|
The [organization] shall enable integrity verification of software and firmware components.{SV-IT-2}{CM-3(5),CM-5(6),CM-10(1),SA-8(9),SA-8(11),SA-8(21),SA-10(1),SI-3,SI-4(24),SI-7,SI-7(10),SI-7(12),SR-4(4)}
|
* The integrity verification mechanisms may include:
** Stipulating and monitoring logical delivery of products and services, requiring downloading from approved, verification-enhanced sites;
** Encrypting elements (software, software patches, etc.) and supply chain process data in transit (motion) and at rest throughout delivery;
** Requiring suppliers to provide their elements “secure by default”, so that additional configuration is required to make the element insecure;
** Implementing software designs using programming languages and tools that reduce the likelihood of weaknesses;
** Implementing cryptographic hash verification; and
** Establishing performance and sub-element baseline for the system and system elements to help detect unauthorized tampering/modification during repairs/refurbishing.
** Stipulating and monitoring logical delivery of products and services, requiring downloading from approved, verification-enhanced sites;
** Encrypting elements (software, software patches, etc.) and supply chain process data in transit (motion) and at rest throughout delivery;
** Requiring suppliers to provide their elements “secure by default”, so that additional configuration is required to make the element insecure;
** Implementing software designs using programming languages and tools that reduce the likelihood of weaknesses;
** Implementing cryptographic hash verification; and
** Establishing performance and sub-element baseline for the system and system elements to help detect unauthorized tampering/modification during repairs/refurbishing.
|
|
For FPGA pre-silicon artifacts that are developed, coded, and tested by a developer that is not accredited, the [organization] shall be subjected to a development environment and pre-silicon artifacts risk assessment by [organization]. Based on the results of the risk assessment, the [organization] may need to implement protective measures or other processes to ensure the integrity of the FPGA pre-silicon artifacts.{SV-SP-5}{SA-3,SA-3(1),SA-8(9),SA-8(11),SA-12,SA-12(1),SR-1,SR-5}
|
DOD-I-5200.44 requires the following:
4.c.2 “Control the quality, configuration, and security of software, firmware, hardware, and systems throughout their lifecycles... Employ protections that manage risk in the supply chain… (e.g., integrated circuits, field-programmable gate arrays (FPGA), printed circuit boards) when they are identifiable (to the supplier) as having a DOD end-use. “ 4.e “In applicable systems, integrated circuit-related products and services shall be procured from a Trusted supplier accredited by the Defense Microelectronics Activity (DMEA) when they are custom-designed, custommanufactured, or tailored for a specific DOD military end use (generally referred to as application-specific integrated circuits (ASIC)). “ 1.g “In coordination with the DOD CIO, the Director, Defense Intelligence Agency (DIA), and the Heads of the DOD Components, develop a strategy for managing risk in the supply chain for integrated circuit-related products and services (e.g., FPGAs, printed circuit boards) that are identifiable to the supplier as specifically created or modified for DOD (e.g., military temperature range, radiation hardened).
|
|
The [organization] shall require the developer of the system, system component, or system services to demonstrate the use of a system development life cycle that includes [state-of-the-practice system/security engineering methods, software development methods, testing/evaluation/validation techniques, and quality control processes].{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-9}{SA-3,SA-4(3)}
|
Examples of good security practices would be using defense-in-depth tactics across the board, least-privilege being implemented, two factor authentication everywhere possible, using DevSecOps, implementing and validating adherence to secure coding standards, performing static code analysis, component/origin analysis for open source, fuzzing/dynamic analysis with abuse cases, etc.
|
|
Any EEEE or mechanical piece parts that cannot be procured from the OCM or their authorized distribution network shall be approved and the government program office notified to prevent and detect counterfeit and fraudulent parts and materials.{SV-SP-5}{SA-8(9),SA-8(11),SA-12,SA-12(1),SR-1,SR-5}
|
The Program, working with the contractors, shall identify which ASICs/FPGAs perform or execute an integral part of mission critical functions and if the supplier is accredited “Trusted” by DMEA. If the contractor is not accredited by DMEA, then the Program may apply various of the below ASIC/FPGA assurance requirements to the contractor, and the Program may need to perform a risk assessment of the contractor’s design environment.
|
|
For ASICs that are designed, developed, manufactured, packaged, or tested by a supplier that is not DMEA accredited, the ASIC development shall undergo a threat/vulnerability risk assessment. Based on the results of the risk assessment, the [organization] may need to implement protective measures or other processes to ensure the integrity of the ASIC.{SV-SP-5}{SA-8(9),SA-8(11),SA-8(21),SA-12,SA-12(1),SR-1,SR-4(4),SR-5}
|
DOD-I-5200.44 requires the following:
4.c.2 “Control the quality, configuration, and security of software, firmware, hardware, and systems throughout their lifecycles... Employ protections that manage risk in the supply chain… (e.g., integrated circuits, field-programmable gate arrays (FPGA), printed circuit boards) when they are identifiable (to the supplier) as having a DOD end-use. “ 4.e “In applicable systems, integrated circuit-related products and services shall be procured from a Trusted supplier accredited by the Defense Microelectronics Activity (DMEA) when they are custom-designed, custommanufactured, or tailored for a specific DOD military end use (generally referred to as application-specific integrated circuits (ASIC)). “ 1.g “In coordination with the DOD CIO, the Director, Defense Intelligence Agency (DIA), and the Heads of the DOD Components, develop a strategy for managing risk in the supply chain for integrated circuit-related products and services (e.g., FPGAs, printed circuit boards) that are identifiable to the supplier as specifically created or modified for DOD (e.g., military temperature range, radiation hardened).
|
|
Any EEEE or mechanical piece parts that cannot be procured from the OCM or their authorized franchised distribution network shall be approved by the [organization]’s Parts, Materials and Processes Control Board (PMPCB) as well as the government program office to prevent and detect counterfeit and fraudulent parts and materials.{SV-SP-5}{SR-1,SR-5}
|
The Program, working with the contractors, shall identify which ASICs/FPGAs perform or execute an integral part of mission critical functions and if the supplier is accredited “Trusted” by DMEA. If the contractor is not accredited by DMEA, then the Program may apply various of the below ASIC/FPGA assurance requirements to the contractor, and the Program may need to perform a risk assessment of the contractor’s design environment.
|
|
For ASICs that are designed, developed, manufactured, packaged, or tested by a supplier that is NOT DMEA accredited Trusted, the ASIC development shall undergo a threat/vulnerability risk assessment.The assessment shall use Aerospace security guidance and requirements tailored from TOR-2019-00506 Vol.2, and TOR-2019-02543 ASIC and FPGA Risk Assessment Process and Checklist.Based on the results of the risk assessment, the Program may require the developer to implement protective measures or other processes to ensure the integrity of the ASIC.{SV-SP-5}{SR-1,SR-5}
|
DOD-I-5200.44 requires the following:
4.c.2 “Control the quality, configuration, and security of software, firmware, hardware, and systems throughout their lifecycles... Employ protections that manage risk in the supply chain… (e.g., integrated circuits, field-programmable gate arrays (FPGA), printed circuit boards) when they are identifiable (to the supplier) as having a DOD end-use. “ 4.e “In applicable systems, integrated circuit-related products and services shall be procured from a Trusted supplier accredited by the Defense Microelectronics Activity (DMEA) when they are custom-designed, custommanufactured, or tailored for a specific DOD military end use (generally referred to as application-specific integrated circuits (ASIC)). “ 1.g “In coordination with the DOD CIO, the Director, Defense Intelligence Agency (DIA), and the Heads of the DOD Components, develop a strategy for managing risk in the supply chain for integrated circuit-related products and services (e.g., FPGAs, printed circuit boards) that are identifiable to the supplier as specifically created or modified for DOD (e.g., military temperature range, radiation hardened).
|
|
For FPGA pre-silicon artifacts that are developed, coded, and tested by a developer that is NOT DMEA accredited Trusted, the contractor/developer shall be subjected to a development environment and pre-silicon artifacts risk assessment by the Program.The assessment shall use Aerospace security guidance and requirements in TOR-2019-00506 Vol.2, and TOR-2019-02543 ASIC and FPGA Risk Assessment Process and Checklist.Based on the results of the risk assessment, the Program may require the developer to implement protective measures or other processes to ensure the integrity of the FPGA pre-silicon artifacts.{SV-SP-5}{SR-1,SR-5}
|
DOD-I-5200.44 requires the following:
4.c.2 “Control the quality, configuration, and security of software, firmware, hardware, and systems throughout their lifecycles... Employ protections that manage risk in the supply chain… (e.g., integrated circuits, field-programmable gate arrays (FPGA), printed circuit boards) when they are identifiable (to the supplier) as having a DOD end-use. “ 4.e “In applicable systems, integrated circuit-related products and services shall be procured from a Trusted supplier accredited by the Defense Microelectronics Activity (DMEA) when they are custom-designed, custommanufactured, or tailored for a specific DOD military end use (generally referred to as application-specific integrated circuits (ASIC)). “ 1.g “In coordination with the DOD CIO, the Director, Defense Intelligence Agency (DIA), and the Heads of the DOD Components, develop a strategy for managing risk in the supply chain for integrated circuit-related products and services (e.g., FPGAs, printed circuit boards) that are identifiable to the supplier as specifically created or modified for DOD (e.g., military temperature range, radiation hardened).
|
|
The [organization] shall ensure that the contractors/developers have all ASICs designed, developed, manufactured, packaged, and tested by suppliers with a Defense Microelectronics Activity (DMEA) Trust accreditation.{SV-SP-5}{SR-1,SR-5}
|
|
|
The [organization] shall ensure that the contractors/developers have all EEEE, and mechanical piece parts procured from the Original Component Manufacturer (OCM) or their authorized franchised distribution network.{SV-SP-5}{SR-1,SR-5}
|
These requirements might only make sense for ASIC/FPGA that are deemed to support mission critical functions. The Program has the responsibility to identify all ASICs and FPGAs that are used in all flight hardware by each hardware element. This list must include all contractor and subcontractor usage of ASICs and FPGAs.
|
|
The [organization] shall use a DMEA certified environment to develop, code and test executable software (firmware or bit-stream) that will be programmed into a one-time programmable FPGA or be programmed into non-volatile memory (NVRAM) that the FPGA executes.{SV-SP-5}{SR-1,SR-5}
|
DOD-I-5200.44 requires the following:
4.c.2 “Control the quality, configuration, and security of software, firmware, hardware, and systems throughout their lifecycles... Employ protections that manage risk in the supply chain… (e.g., integrated circuits, field-programmable gate arrays (FPGA), printed circuit boards) when they are identifiable (to the supplier) as having a DOD end-use. “ 4.e “In applicable systems, integrated circuit-related products and services shall be procured from a Trusted supplier accredited by the Defense Microelectronics Activity (DMEA) when they are custom-designed, custommanufactured, or tailored for a specific DOD military end use (generally referred to as application-specific integrated circuits (ASIC)). “ 1.g “In coordination with the DOD CIO, the Director, Defense Intelligence Agency (DIA), and the Heads of the DOD Components, develop a strategy for managing risk in the supply chain for integrated circuit-related products and services (e.g., FPGAs, printed circuit boards) that are identifiable to the supplier as specifically created or modified for DOD (e.g., military temperature range, radiation hardened).
|
|
The [spacecraft] shall monitor security relevant telemetry points for malicious commanding attempts.{AC-17,AC-17(1),AC-17(10),AU-3(1),RA-10,SC-7,SC-16,SC-16(2),SC-16(3),SI-3(8),SI-4,SI-4(1),SI-4(13),SI-4(24),SI-4(25),SI-10(6)}
|
|
|
The [spacecraft] shall accept hazardous commands only when prerequisite checks are satisfied.{AC-17(4),SI-10,SI-10(6)}
|
|
|
The [spacecraft] shall protect authenticator content from unauthorized disclosure and modification.{SV-AC-1,SV-AC-3}{AC-17(6),CM-3(6),IA-5,IA-5(6),RA-5(4),SA-8(18),SA-8(19),SC-28(3)}
|
|
|
The [spacecraft] encryption key handling shall be handled outside of the onboard software and protected using cryptography.{SV-AC-1,SV-AC-3}{AC-17(6),CM-3(6),SA-8(19),SA-9(6),SC-8(1),SC-12,SC-28(1),SC-28(3)}
|
|
|
The [spacecraft] encryption keys shall be restricted so that the onboard software is not able to access the information for key readout.{SV-AC-1,SV-AC-3}{AC-17(6),CM-3(6),SA-8(19),SA-9(6),SC-8(1),SC-12,SC-28(3)}
|
|
|
The [spacecraft] encryption keys shall be restricted so that they cannot be read via any telecommands.{SV-AC-1,SV-AC-3}{AC-17(6),CM-3(6),SA-8(19),SA-9(6),SC-8(1),SC-12,SC-28(3)}
|
|
|
The [spacecraft] shall produce, control, and distribute symmetric cryptographic keys using NSA Certified or Approved key management technology and processes per CNSSP 12.{SV-AC-1,SV-AC-3}{AC-17(6),CM-3(6),SA-9(6),SC-12,SC-12(1),SC-12(2),SC-12(3)}
|
|
|
The [spacecraft] shall provide the capability to restrict command lock based on geographic location of ground stations.{SV-AC-1}{AC-2(11),IA-10,SI-4(13),SI-4(25)}
|
This could be performed using command lockout based upon when the spacecraft is over selected regions. This should be configurable so that when conflicts arise, the Program can update. The goal is so the spacecraft won't accept a command when the spacecraft determines it is in a certain region.
|
|
The [spacecraft] shall restrict the use of information inputs to spacecraft and designated ground stations as defined in the applicable ICDs.{SV-AC-1,SV-AC-2}{AC-20,SC-23,SI-10,SI-10(5),SI-10(6)}
|
|
|
The [spacecraft] shall implement a reference monitor mechanism that mediates access between subjects and objects based on a defined set of rules, that is designed and configured to resist tampering or unauthorized alteration, providing a reliable and secure foundation for access control within the information system.{AC-25}
|
|
|
The [spacecraft] shall authenticate the ground station (and all commands) and other spacecraft before establishing remote connections using bidirectional authentication that is cryptographically based.{SV-AC-1,SV-AC-2}{AC-3,AC-17,AC-17(2),AC-17(10),AC-18(1),AC-20,IA-3(1),IA-4,IA-4(9),IA-7,IA-9,SA-8(18),SA-8(19),SA-9(2),SC-7(11),SC-16(1),SC-16(2),SC-16(3),SC-23(3),SI-3(9)}
|
Authorization can include embedding opcodes in command strings, using trusted authentication protocols, identifying proper link characteristics such as emitter location, expected range of receive power, expected modulation, data rates, communication protocols, beamwidth, etc.; and tracking command counter increments against expected values.
|
|
The [spacecraft] shall implement cryptographic mechanisms to identify and reject wireless transmissions that are deliberate attempts to achieve imitative or manipulative communications deception based on signal parameters.{SV-AV-1,SV-IT-1}{AC-3,AC-20,SA-8(19),SC-8(1),SC-23(3),SC-40(3),SI-4(13),SI-4(24),SI-4(25),SI-10(6)}
|
|
|
The [spacecraft] shall employ the principle of least privilege, allowing only authorized accesses processes which are necessary to accomplish assigned tasks in accordance with system functions.{SV-AC-6}{AC-3,AC-6,AC-6(9),CA-9,CM-5,CM-5(5),CM-5(6),SA-8(2),SA-8(5),SA-8(6),SA-8(14),SA-8(23),SA-17(7),SC-2,SC-7(29),SC-32,SC-32(1),SI-3}
|
|
|
The [spacecraft] shall implement relay and replay-resistant authentication mechanisms for establishing a remote connection.{SV-AC-1,SV-AC-2}{AC-3,IA-2(8),IA-2(9),SA-8(18),SC-8(1),SC-16(1),SC-16(2),SC-23(3),SC-40(4)}
|
|
|
The [spacecraft] shall ensure that processes reusing a shared system resource (e.g., registers, main memory, secondary storage) do not have access to information (including encrypted representations of information) previously stored in that resource during a prior use by a process after formal release of that resource back to the system or reuse.{SV-AC-6}{AC-3,PM-32,SA-8(2),SA-8(5),SA-8(6),SA-8(19),SC-4,SI-3}
|
|
|
The [spacecraft] shall protect the confidentiality and integrity of the following information using cryptography while it is at rest: [all information].{AC-3,SA-8(19),SC-28,SC-28(1),SI-7(6)}
|
* The intent as written is for all transmitted traffic to be protected. This includes internal to internal communications and especially outside of the boundary.
|
|
The [spacecraft] shall maintain the confidentiality and integrity of information during preparation for transmission and during reception.{SV-AC-7}{AC-3,SA-8(19),SC-8,SC-8(1),SC-8(2),SC-16,SC-16(1)}
|
* Preparation for transmission and during reception includes the aggregation, packing, and transformation options performed prior to transmission and the undoing of those operations that occur upon receipt.
|
|
The [spacecraft] shall encrypt all telemetry on downlink regardless of operating mode to protect current state of spacecraft.{SV-CF-4}{AC-3(10),RA-5(4),SA-8(18),SA-8(19),SC-8,SC-8(1),SC-13}
|
|
|
The [spacecraft] shall not employ a mode of operations where cryptography on the TT&C link can be disabled (i.e., crypto-bypass mode).{SV-AC-1,SV-CF-1,SV-CF-2}{AC-3(10),SA-8(18),SA-8(19),SC-16(2),SC-16(3),SC-40(4)}
|
|
|
The [spacecraft] shall require multi-factor authorization for all spacecraft [applications or operating systems] updates within the spacecraft.{SV-SP-9,SV-SP-11}{AC-3(2),CM-3(8),CM-5,PM-12,SA-8(8),SA-8(31),SA-10(2),SI-3(8),SI-7(12),SI-10(6)}
|
The intent is for multiple checks to be performed prior to executing these SV SW updates. One action is mere act of uploading the SW to the spacecraft. Another action could be check of digital signature (ideal but not explicitly required) or hash or CRC or a checksum. Crypto boxes provide another level of authentication for all commands, including SW updates but ideally there is another factor outside of crypto to protect against FSW updates. Multi-factor authorization could be the "two-man rule" where procedures are in place to prevent a successful attack by a single actor (note: development activities that are subsequently subject to review or verification activities may already require collaborating attackers such that a "two-man rule" is not appropriate).
|
|
The [spacecraft] shall provide two independent and unique command messages to deactivate a fault tolerant capability for a critical or catastrophic hazard.{AC-3(2),PE-10,SA-8(15)}
|
|
|
The [spacecraft] shall provide non-identical methods, or functionally independent methods, for commanding a mission critical function when the software is the sole control of that function.{AC-3(2),SI-3(8),SI-13}
|
|
|
The [spacecraft] shall enforce approved authorizations for controlling the flow of information within the platform and between interconnected systems so that information does not leave the platform boundary unless it is encrypted.{SV-AC-6}{AC-3(3),AC-3(4),AC-4,AC-4(6),AC-4(21),CA-3,CA-3(6),CA-3(7),CA-9,IA-9,SA-8(19),SC-8(1),SC-16(3)}
|
|
|
The [spacecraft] security implementation shall ensure that information should not be allowed to flow between partitioned applications unless explicitly permitted by the system.{AC-3(3),AC-3(4),AC-4,AC-4(6),AC-4(21),CA-9,IA-9,SA-8(3),SA-8(18),SA-8(19),SC-2(2),SC-7(29),SC-16,SC-32}
|
|
|
The [spacecraft] shall, when transferring information between different security domains, implements the following security policy filters that require fully enumerated formats that restrict data structure and content: connectors and semaphores implemented in the RTOS.{SV-AC-6}{AC-3(3),AC-3(4),AC-4(14),IA-9,SA-8(19),SC-16}
|
|
|
The [spacecraft] shall implement boundary protections to separate bus, communications, and payload components supporting their respective functions.{SV-AC-6}{AC-3(3),AC-3(4),CA-9,SA-8(3),SA-8(14),SA-8(18),SA-8(19),SA-17(7),SC-2,SC-2(2),SC-7(13),SC-7(21),SC-7(29),SC-16(3),SC-32,SI-3,SI-4(13),SI-4(25)}
|
|
|
The [spacecraft] shall isolate mission critical functionality from non-mission critical functionality by means of an isolation boundary (e.g.via partitions) that controls access to and protects the integrity of, the hardware, software, and firmware that provides that functionality.{SV-AC-6}{AC-3(3),AC-3(4),CA-9,SA-8(3),SA-8(19),SA-17(7),SC-2,SC-3,SC-3(4),SC-7(13),SC-7(29),SC-32,SC-32(1),SI-3,SI-7(10),SI-7(12)}
|
|
|
The [spacecraft] data within partitioned applications shall not be read or modified by other applications/partitions.{SV-AC-6}{AC-3(3),AC-3(4),SA-8(19),SC-2(2),SC-4,SC-6,SC-32}
|
|
|
The [spacecraft] shall prevent unauthorized access to system resources by employing an efficient capability based object model that supports both confinement and revocation of these capabilities when the platform security deems it necessary.{SV-AC-6}{AC-3(8),IA-4(9),PM-32,SA-8(2),SA-8(5),SA-8(6),SA-8(18),SA-8(19),SC-2(2),SC-4,SC-16,SC-32,SI-3}
|
|
|
The [spacecraft] shall use protected processing domains to enforce the policy that information does not leave the platform boundary unless it is encrypted as a basis for flow control decisions.{SV-AC-6}{AC-4(2),IA-9,SA-8(19),SC-8(1),SC-16(3)}
|
|
|
The [spacecraft] shall define the security functions and security-relevant information for which the system must protect from unauthorized access.{AC-6(1),SA-8(19),SC-7(13),SC-16}
|
|
|
The [spacecraft] shall monitor and collect all onboard cyber-relevant data (from multiple system components), including identification of potential attacks and sufficient information about the attack for subsequent analysis.{SV-DCO-1}{AC-6(9),AC-20,AC-20(1),AU-2,AU-12,IR-4,IR-4(1),RA-10,SI-3,SI-3(10),SI-4,SI-4(1),SI-4(2),SI-4(7),SI-4(24)}
|
The spacecraft will monitor and collect data that provides accountability of activity occurring onboard the spacecraft. Due to resource limitations on the spacecraft, analysis must be performed to determine which data is critical for retention and which can be filtered. Full system coverage of data and actions is desired as an objective; it will likely be impractical due to the resource limitations. “Cyber-relevant data” refers to all data and actions deemed necessary to support accountability and awareness of onboard cyber activities for the mission. This would include data that may indicate abnormal activities, critical configuration parameters, transmissions on onboard networks, command logging, or other such data items. This set of data items should be identified early in the system requirements and design phase. Cyber-relevant data should support the ability to assess whether abnormal events are unintended anomalies or actual cyber threats. Actual cyber threats may rarely or never occur, but non-threat anomalies occur regularly. The ability to filter out cyber threats for non-cyber threats in relevant time would provide a needed capability. Examples could include successful and unsuccessful attempts to access, modify, or delete privileges, security objects, security levels, or categories of information (e.g., classification levels).
|
|
The [spacecraft] shall provide the capability to modify the set of audited events (e.g., cyber-relevant data).{SV-DCO-1}{AU-12(3),AU-14}
|
|
|
The [spacecraft] shall generate cyber-relevant audit records containing information that establishes what type of event occurred, when the event occurred, where the event occurred, the source of the event, and the outcome of the event.{SV-DCO-1}{AU-3,AU-3(1),AU-12,IR-4,IR-4(1),RA-10,SI-3,SI-3(10),SI-4(7),SI-4(24)}
|
|
|
The [spacecraft] shall be configured to allocate audit record storage capacity in accordance with 1 week audit record storage requirements.{SV-DCO-1}{AU-4,AU-5,AU-5(1),AU-5(2)}
|
|
|
The [spacecraft] shall downlink relevant audit log data to ground systems frequently enough to avoid any situation where audit storage capacity is exceeded.{AU-4(1)}
|
The frequency of offloading this data depends on the amount of data being audited/logged and will vary across missions/systems.
|
|
The [spacecraft] shall attribute cyber attacks and identify unauthorized use of the platform by downlinking onboard cyber information to the mission ground station within 3 minutes. {AU-4(1),IR-4,IR-4(1),IR-4(12),IR-4(13),RA-10,SA-8(22),SI-3,SI-3(10),SI-4(5),SI-4(7),SI-4(12),SI-4(24)}
|
|
|
The [spacecraft] shall attribute cyberattacks and identify unauthorized use of the spacecraft by downlinking onboard cyber information to the mission ground station within [mission-appropriate timelines minutes].{SV-DCO-1}{AU-4(1),SI-4(5)}
|
Requirement is to support offboard attribution by enabling the fusion of spacecraft cyber data with ground-based cyber data. This would provide end-to-end accountability of commands, data, and other data that can be used to determine the origin of attack from the ground system. Data should be provided within time constraints relevant for the particular mission and its given operational mode. Analysis should be performed to identify the specific timeliness requirements for a mission, which may vary depending on mission mode, operational status, availability of communications resources, and other factors. The specific data required should be identified, as well.
|
|
The [spacecraft] shall alert in the event of the [organization]-defined audit/logging processing failures.{SV-DCO-1}{AU-5}
|
|
|
The [spacecraft] shall alert in the event of the audit/logging processing failures.{AU-5,AU-5(1),AU-5(2),SI-3,SI-4,SI-4(1),SI-4(7),SI-4(12),SI-4(24)}
|
|
|
The [spacecraft] shall provide an alert immediately to [at a minimum the mission director, administrators, and security officers] when the following failure events occur: [minimally but not limited to: auditing software/hardware errors; failures in the audit capturing mechanisms; and audit storage capacity reaching 95%, 99%, and 100%] of allocated capacity.{SV-DCO-1}{AU-5,AU-5(1),AU-5(2),SI-4,SI-4(1),SI-4(7),SI-4(12),SI-4(24),SI-7(7)}
|
Intent is to have human on the ground be alerted to failures. This can be decomposed to SV to generate telemetry and to Ground to alert.
|
|
The [spacecraft] shall provide the capability of a cyber “black-box” to capture necessary data for cyber forensics of threat signatures and anomaly resolution when cyber attacks are detected.{SV-DCO-1}{AU-5(5),AU-9(2),AU-9(3),AU-12,IR-4(12),IR-4(13),IR-5(1),SI-3,SI-3(10),SI-4,SI-4(1),SI-4(7),SI-4(24),SI-7(7)}
|
Similar concept of a "black box" on an aircraft where all critical information is stored for post forensic analysis. Black box can be used to record CPU utilization, GNC physical parameters, audit records, memory contents, TT&C data points, etc. The timeframe is dependent upon implementation but needs to meet the intent of the requirement. For example, 30 days may suffice.
|
|
The [spacecraft] shall provide automated onboard mechanisms that integrate audit review, analysis, and reporting processes to support mission processes for investigation and response to suspicious activities to determine the attack class in the event of a cyber attack.{SV-DCO-1}{AU-6(1),IR-4,IR-4(1),IR-4(12),IR-4(13),PM-16(1),RA-10,SA-8(21),SA-8(22),SC-5(3),SI-3,SI-3(10),SI-4(7),SI-4(24),SI-7(7)}
|
* Identifying the class (e.g., exfiltration, Trojans, etc.), nature, or effect of cyberattack (e.g., exfiltration, subverted control, or mission interruption) is necessary to determine the type of response. The first order of identification may be to determine whether the event is an attack or a non-threat event (anomaly). The objective requirement would be to predict the impact of the detected signature.
* Unexpected conditions can include RF lockups, loss of lock, failure to acquire an expected contact and unexpected reports of acquisition, unusual AGC and ACS control excursions, unforeseen actuator enabling's or actions, thermal stresses, power aberrations, failure to authenticate, software or counter resets, etc. Mitigation might include additional TMONs, more detailed AGC and PLL thresholds to alert operators, auto-capturing state snapshot images in memory when unexpected conditions occur, signal spectra measurements, and expanded default diagnostic telemetry modes to help in identifying and resolving anomalous conditions.
|
|
The [organization] shall integrate terrestrial system audit log analysis as part of the standard anomaly resolution process to correlate any anomalous behavior in the terrestrial systems that correspond to anomalous behavior in the spacecraft.{SV-DCO-1}{AU-6(1),IR-5(1)}
|
|
|
The [spacecraft] shall integrate cyber related detection and responses with existing fault management capabilities to ensure tight integration between traditional fault management and cyber intrusion detection and prevention.{SV-DCO-1}{AU-6(4),IR-4,IR-4(1),RA-10,SA-8(21),SA-8(26),SC-3(4),SI-3,SI-3(10),SI-4(7),SI-4(13),SI-4(16),SI-4(24),SI-4(25),SI-7(7),SI-13}
|
The onboard IPS system should be integrated into the existing onboard spacecraft fault management system (FMS) because the FMS has its own fault detection and response system built in. SV corrective behavior is usually limited to automated fault responses and ground commanded recovery actions. Intrusion prevention and response methods will inform resilient cybersecurity design. These methods enable detected threat activity to trigger defensive responses and resilient SV recovery.
|
|
The [spacecraft] shall record time stamps for audit records that can be mapped to Coordinated Universal Time (UTC) or Greenwich Mean Time (GMT).{SV-DCO-1}{AU-8}
|
|
|
The [spacecraft] shall record time stamps for audit records that provide a granularity of one Z-count (1.5 sec).{SV-DCO-1}{AU-8}
|
|
|
The [spacecraft] shall use internal system clocks to generate time stamps for audit records.{SV-DCO-1}{AU-8}
|
|
|
The [spacecraft] shall protect information obtained from logging/intrusion-monitoring from unauthorized access, modification, and deletion.{SV-DCO-1}{AU-9,AU-9(3),RA-10,SI-4(7),SI-4(24)}
|
|
|
The [spacecraft] shall implement cryptographic mechanisms to protect the integrity of audit information and audit tools.{SV-DCO-1}{AU-9(3),RA-10,SC-8(1),SI-3,SI-3(10),SI-4(24)}
|
|
|
All [spacecraft] commands which have unrecoverable consequence must have dual authentication prior to command execution.{AU-9(5),IA-3,IA-4,IA-10,PE-3,PM-12,SA-8(15),SA-8(21),SC-16(2),SC-16(3),SI-3(8),SI-3(9),SI-4(13),SI-4(25),SI-7(12),SI-10(6),SI-13}
|
|
|
The [spacecraft] shall have a method to ensure the integrity of these commands and validate their authenticity before execution.{AU-9(5),IA-3,IA-4,IA-10,PE-3,PM-12,SA-8(15),SA-8(21),SC-16(2),SC-16(3),SI-3(8),SI-3(9),SI-4(13),SI-4(25),SI-7(12),SI-10(6),SI-13}
|
|
|
The [organization] shall ensure that the allocated security safeguards operate in a coordinated and mutually reinforcing manner.{SV-MA-6}{CA-7(5),PL-7,PL-8(1),SA-8(19)}
|
|
|
The [organization] shall document and design a security architecture using a defense-in-depth approach that allocates the [organization]s defined safeguards to the indicated locations and layers: [Examples include: operating system abstractions and hardware mechanisms to the separate processors in the platform, internal components, and the FSW].{SV-MA-6}{CA-9,PL-7,PL-8,PL-8(1),SA-8(3),SA-8(4),SA-8(7),SA-8(9),SA-8(11),SA-8(13),SA-8(19),SA-8(29),SA-8(30)}
|
|
|
The [spacecraft] shall use automated mechanisms to maintain and validate baseline configuration to ensure the [spacecraft] is up-to-date, complete, accurate, and readily available.{SV-SP-3}{CM-2(2),CM-3(5),CM-3(7),CM-6,SA-8(8)}
|
This could be command trigger from Ground or elsewhere. The point here is that the self-test is executed onboard the spacecraft via onboard HW/SW self-test mechanisms and its result is reported to the Ground
|
|
The [spacecraft] shall prevent the installation of Flight Software without verification that the component has been digitally signed using a certificate that is recognized and approved by the ground.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-9}{CM-3,CM-3(8),CM-5,CM-5(3),CM-14,SA-8(8),SA-8(31),SA-10(2),SI-3,SI-7(12),SI-7(15)}
|
|
|
The [organization] shall employ automated tools that provide notification to ground operators upon discovering discrepancies during integrity verification.{CM-3(5),CM-6,IR-6,IR-6(2),SA-8(21),SC-51,SI-3,SI-4(7),SI-4(12),SI-4(24),SI-7(2)}
|
|
|
The [spacecraft] shall provide automatic notification to ground operators upon discovering discrepancies during integrity verification.{SV-IT-2}{CM-3(5),SA-8(21),SI-3,SI-4(7),SI-4(12),SI-4(24),SI-7(2)}
|
|
|
The [spacecraft], upon detection of a potential integrity violation, shall provide the capability to [audit the event and alert ground operators].{SV-DCO-1}{CM-3(5),SA-8(21),SI-3,SI-4(7),SI-4(12),SI-4(24),SI-7(8)}
|
One example would be for bad commands where the system would reject the command and not increment the Vehicle Command Counter (VCC) and include the information in telemetry.
|
|
The [spacecraft] shall execute procedures for ensuring that security-relevant hardware, software, and firmware updates uploaded are exactly as specified by the gold copies. {CM-3(5),SA-8(8),SA-8(21),SA-8(31),SA-10(3),SA-10(4),SA-10(6),SI-7(10),SI-7(12)}
|
|
|
The [spacecraft] shall perform an integrity check of software, firmware, and information at startup or during security-relevant events. {CM-3(5),SA-8(9),SA-8(11),SA-8(21),SI-3,SI-7(1),SI-7(10),SI-7(12),SI-7(17)}
|
|
|
The [spacecraft] shall enforce access restrictions associated with changes to the spacecraft.{CM-5}
|
|
|
The [spacecraft] shall be configured to provide only essential capabilities.{CM-6,CM-7,SA-8(2),SA-8(7),SA-8(13),SA-8(23),SA-8(26),SA-15(5)}
|
|
|
The [organization] shall ensure that software planned for reuse meets the fit, form, and function, and security as a component within the new application.{SV-SP-6,SV-SP-7,SV-SP-11}{CM-7(5)}
|
|
|
The [spacecraft] operating system, if COTS or FOSS, shall be selected from a [organization]-defined acceptance list.{SV-SP-7}{CM-7(8),CM-7(5)}
|
|
|
The [spacecraft] and all ground support systems (including those during development) shall be capable of detecting unauthorized hardware components/connections.{CM-7(9)}
|
|
|
The [spacecraft] shall enter a cyber-safe mode when conditions that threaten the platform are detected, enters a cyber-safe mode of operation with restrictions as defined based on the cyber-safe mode.{SV-AV-5,SV-AV-6,SV-AV-7}{CP-10(6),CP-12,CP-13,IR-4,IR-4(1),IR-4(3),PE-10,RA-10,SA-8(16),SA-8(21),SA-8(24),SI-3,SI-4(7),SI-13,SI-17}
|
|
|
The [spacecraft] shall provide the capability to enter the platform into a known good, operational cyber-safe mode from a tamper-resistant, configuration-controlled (“gold”) image that is authenticated as coming from an acceptable supplier, and has its integrity verified.{SV-AV-5,SV-AV-6,SV-AV-7}{CP-10(6),CP-12,CP-13,IR-4(3),SA-8(16),SA-8(19),SA-8(21),SA-8(24),SI-13,SI-17}
|
Cyber-safe mode is an operating mode of a spacecraft during which all nonessential systems are shut down and the spacecraft is placed in a known good state using validated software and configuration settings. Within cyber-safe mode authentication and encryption should still be enabled. The spacecraft should be capable of reconstituting firmware and SW functions to preattack levels to allow for the recovery of functional capabilities. This can be performed by self-healing, or the healing can be aided from the ground. However, the spacecraft needs to have the capability to replan, based on available equipment still available after a cyberattack. The goal is for the vehicle to resume full mission operations. If not possible, a reduced level of mission capability should be achieved.
|
|
The [spacecraft] shall enter cyber-safe mode software/configuration should be stored onboard the spacecraft in memory with hardware-based controls and should not be modifiable.{CP-10(6),CP-13,SA-8(16),SA-8(19),SA-8(21),SA-8(24),SI-17}
|
|
|
The [spacecraft] shall fail to a known secure state for failures during initialization, and aborts preserving information necessary to return to operations in failure.{SV-AV-5,SV-AV-6,SV-AV-7}{CP-10(6),CP-13,SA-8(16),SA-8(19),SA-8(24),SC-24,SI-13,SI-17}
|
|
|
The [spacecraft] shall fail securely to a secondary device in the event of an operational failure of a primary boundary protection device (i.e., crypto solution).{SV-AC-1,SV-AC-2,SV-CF-1,SV-CF-2}{CP-13,SA-8(19),SA-8(24),SC-7(18),SI-13,SI-13(4)}
|
|
|
The [organization] shall define the security safeguards that are to be automatically employed when integrity violations are discovered.{SV-IT-2}{CP-2,SA-8(21),SI-3,SI-4(7),SI-4(12),SI-7(5),SI-7(8)}
|
|
|
The [spacecraft] shall recover from cyber-safe mode to mission operations within 20 minutes.{SV-MA-5}{CP-2(3),CP-2(5),IR-4,SA-8(24)}
|
Upon conclusion of addressing the threat, the system should be capable of recovering from the minimal survival mode back into a mission-ready state within defined timelines. The intent is to define the timelines and the capability to return back to mission operations.
|
|
The [spacecraft] shall provide or support the capability for recovery and reconstitution to a known state after a disruption, compromise, or failure.{SV-AV-5,SV-AV-6,SV-AV-7}{CP-4(4),CP-10,CP-10(4),CP-10(6),CP-13,IR-4,IR-4(1),SA-8(16),SA-8(19),SA-8(24)}
|
|
|
The [spacecraft] shall have multiple uplink paths {SV-AV-1}{CP-8,CP-11,SA-8(18),SC-5,SC-47}
|
|
|
The [spacecraft] shall utilize TRANSEC.{SV-AV-1}{CP-8,RA-5(4),SA-8(18),SA-8(19),SC-8(1),SC-8(4),SC-16,SC-16(1),SC-16(2),SC-16(3),SC-40(4)}
|
Transmission Security (TRANSEC) is used to ensure the availability of transmissions and limit intelligence collection from the transmissions. TRANSEC is secured through burst encoding, frequency hopping, or spread spectrum methods where the required pseudorandom sequence generation is controlled by a cryptographic algorithm and key. Such keys are known as transmission security keys (TSK). The objectives of transmission security are low probability of interception (LPI), low probability of detection (LPD), and antijam which means resistance to jamming (EPM or ECCM).
|
|
The [spacecraft] shall be able to locate the onboard origin of a cyber attack and alert ground operators within 3 minutes.{SV-DCO-1}{IR-4,IR-4(1),IR-4(12),IR-4(13),RA-10,SA-8(22),SI-3,SI-3(10),SI-4,SI-4(1),SI-4(7),SI-4(12),SI-4(16),SI-4(24)}
|
The origin of any attack onboard the vehicle should be identifiable to support mitigation. At the very least, attacks from critical element (safety-critical or higher-attack surface) components should be locatable quickly so that timely action can occur.
|
|
The [spacecraft] shall detect and deny unauthorized outgoing communications posing a threat to the spacecraft.{SV-DCO-1}{IR-4,IR-4(1),RA-5(4),RA-10,SC-7(9),SC-7(10),SI-4,SI-4(1),SI-4(4),SI-4(7),SI-4(11),SI-4(13),SI-4(24),SI-4(25)}
|
|
|
The [spacecraft] shall recover to a known cyber-safe state when an anomaly is detected.{IR-4,IR-4(1),SA-8(16),SA-8(19),SA-8(21),SA-8(24),SI-3,SI-4(7),SI-10(6),SI-13,SI-17}
|
|
|
The [spacecraft] shall detect and recover from detected memory errors or transitions to a known cyber-safe state.{IR-4,IR-4(1),SA-8(16),SA-8(24),SI-3,SI-4(7),SI-10(6),SI-13,SI-17}
|
|
|
The [spacecraft] shall select and execute safe countermeasures against cyber attacks prior to entering cyber-safe mode.{SV-DCO-1}{IR-4,RA-10,SA-8(21),SA-8(24),SI-4(7),SI-17}
|
These countermeasures are a ready supply of options to triage against the specific types of attack and mission priorities. Minimally, the response should ensure vehicle safety and continued operations. Ideally, the goal is to trap the threat, convince the threat that it is successful, and trace and track the attacker exquisitely—with or without ground aiding. This would support successful attribution and evolving countermeasures to mitigate the threat in the future. “Safe countermeasures” are those that are compatible with the system’s fault management system to avoid unintended effects or fratricide on the system." These countermeasures are likely executed prior to entering into a cyber-safe mode.
|
|
The [spacecraft] shall provide cyber threat status to the ground segment for the Defensive Cyber Operations team, per the governing specification.{SV-DCO-1}{IR-5,PM-16,PM-16(1),RA-3(3),RA-10,SI-4,SI-4(1),SI-4(24),SI-7(7)}
|
The future space enterprises will include full-time Cyber Defense teams supporting space mission systems. Their work is currently focused on the ground segment but may eventually require specific data from the space segment for their successful operation. This requirement is a placeholder to ensure that any DCO-related requirements are taken into consideration for this document.
|
|
The [spacecraft] shall be capable of shutting off specific subsystems or payloads to isolate malicious activity or protect the platform.{PE-10}
|
|
|
The [spacecraft] shall perform an orderly, controlled system shut-down to a known cyber-safe state upon receipt of a termination command or condition.{PE-11,PE-11(1),SA-8(16),SA-8(19),SA-8(24),SI-17}
|
|
|
The [spacecraft] shall operate securely in off-nominal power conditions, including loss of power and spurious power transients.{PE-11,PE-11(1),SA-8(16),SA-8(19),SI-13,SI-17}
|
|
|
The [spacecraft] shall protect system components, associated data communications, and communication buses in accordance with: (i) national emissions and TEMPEST policies and procedures, and (ii) the security category or sensitivity of the transmitted information.{SV-CF-2,SV-MA-2}{PE-14,PE-19,PE-19(1),RA-5(4),SA-8(18),SA-8(19),SC-8(1)}
|
The measures taken to protect against compromising emanations must be in accordance with DODD S-5200.19, or superseding requirements. The concerns addressed by this control during operation are emanations leakage between multiple payloads within a single space platform, and between payloads and the bus.
|
|
The [spacecraft] shall be designed such that it protects itself from information leakage due to electromagnetic signals emanations.{SV-CF-2,SV-MA-2}{PE-19,PE-19(1),RA-5(4),SA-8(19)}
|
This requirement applies if system components are being designed to address EMSEC and the measures taken to protect against compromising emanations must be in accordance with DODD S-5200.19, or superseding requirements.
|
|
The [organization] shall implement a security architecture and design that provides the required security functionality, allocates security controls among physical and logical components, and integrates individual security functions, mechanisms, and processes together to provide required security capabilities and a unified approach to protection.{SV-MA-6}{PL-7,SA-2,SA-8,SA-8(1),SA-8(2),SA-8(3),SA-8(4),SA-8(5),SA-8(6),SA-8(7),SA-8(9),SA-8(11),SA-8(13),SA-8(19),SA-8(29),SA-8(30),SC-32,SC-32(1)}
|
|
|
The [spacecraft] shall prevent unauthorized and unintended information transfer via shared system resources.{SV-AC-6}{PM-32,SA-8(2),SA-8(5),SA-8(6),SA-8(19),SC-2(2),SC-4}
|
|
|
The [spacecraft] shall be designed and configured so that encrypted communications traffic and data is visible to on-board security monitoring tools.{SV-DCO-1}{RA-10,SA-8(21),SI-3,SI-3(10),SI-4,SI-4(1),SI-4(10),SI-4(13),SI-4(24),SI-4(25)}
|
|
|
The [spacecraft] shall be designed and configured so that spacecraft memory can be monitored by the on-board intrusion detection/prevention capability.{SV-DCO-1}{RA-10,SA-8(21),SI-3,SI-3(10),SI-4,SI-4(1),SI-4(24),SI-16}
|
|
|
The [spacecraft] shall have on-board intrusion detection/prevention system that monitors the mission critical components or systems.{SV-AC-1,SV-AC-2,SV-MA-4}{RA-10,SC-7,SI-3,SI-3(8),SI-4,SI-4(1),SI-4(7),SI-4(13),SI-4(24),SI-4(25),SI-10(6)}
|
The mission critical components or systems could be GNC/Attitude Control, C&DH, TT&C, Fault Management.
|
|
The [spacecraft] shall employ advanced analytics capabilities within the IDS/IPS to address dynamic never-before-seen attacks using machine learning/adaptive technologies along with signature-based attacks.{RA-3(4)}
|
|
|
The [spacecraft] shall generate error messages that provide information necessary for corrective actions without revealing information that could be exploited by adversaries.{SV-AV-5,SV-AV-6,SV-AV-7}{RA-5(4),SI-4(12),SI-11}
|
|
|
The [spacecraft] shall reveal error messages only to operations personnel monitoring the telemetry.{SV-AV-5,SV-AV-6,SV-AV-7}{RA-5(4),SI-4(12),SI-11}
|
|
|
The [spacecraft] shall retain the capability to update/upgrade operating systems while on-orbit.{SV-SP-7}{SA-4(5),SA-8(8),SA-8(31),SA-10(2),SI-3}
|
The operating system updates should be performed using multi-factor authorization and should only be performed when risk of compromise/exploitation of identified vulnerability outweighs the risk of not performing the update.
|
|
The [organization] shall define acceptable secure communication protocols available for use within the mission in accordance with applicable federal laws, Executive Orders, directives, policies, regulations, and standards.{SV-AC-7}{SA-4(9)}
|
The secure communication protocol should include "strong" authenticated encryption characteristics.
|
|
The [spacecraft] shall only use [organization]-defined communication protocols within the mission.{SV-AC-7}{SA-4(9)}
|
|
|
The [spacecraft] shall only use communication protocols that support encryption within the mission.{SA-4(9),SA-8(18),SA-8(19),SC-40(4)}
|
|
|
The [spacecraft] boot firmware must validate the boot loader, boot configuration file, and operating system image, in that order, against their respective signatures.{SV-IT-3}{SA-8(10),SA-8(11),SA-8(12),SI-7(9),SI-7(10)}
|
A signature is ~770 bits long. No requirement is imposed on the storage location of signatures.
|
|
The [spacecraft] boot firmware must verify a trust chain that extends through the hardware root of trust, boot loader, boot configuration file, and operating system image, in that order.{SV-IT-3}{SA-8(10),SA-8(11),SA-8(12),SI-7(9),SI-7(10)}
|
These three items were chosen because they’re intended to be static values (once properly set up) but are in volatile storage. Also, the Boot ROM can’t be modified, so there’s no reason to check a signature.
|
|
The [spacecraft] trusted boot/RoT computing module shall be implemented on radiation tolerant burn-in (non-programmable) equipment.{SA-8(10),SA-8(11),SA-8(12),SI-7(9),SI-7(10)}
|
|
|
The [spacecraft] trusted boot/RoT shall be a separate compute engine controlling the trusted computing platform cryptographic processor.{SA-8(10),SA-8(11),SA-8(12),SI-7(9),SI-7(10)}
|
|
|
The [spacecraft] shall perform attestation at each stage of startup and ensure overall trusted boot regime (i.e., root of trust).{SV-IT-3}{SA-8(10),SA-8(11),SA-8(12),SI-7(9),SI-7(10),SI-7(17)}
|
It is important for the computing module to be able to access a set of functions and commands that it trusts; that is, that it knows to be true. This concept is referred to as root of trust (RoT) and should be included in the spacecraft design. With RoT, a device can always be trusted to operate as expected. RoT functions, such as verifying the device’s own code and configuration, must be implemented in secure hardware (i.e., field programmable gate arrays). By checking the security of each stage of power-up, RoT devices form the first link in a chain of trust that protects the spacecraft
|
|
The [spacecraft] shall maintain a separate execution domain for each executing process.{SV-AC-6}{SA-8(14),SA-8(19),SC-2(2),SC-7(21),SC-39,SI-3}
|
|
|
The [spacecraft] flight software must not be able to tamper with the security policy or its enforcement mechanisms.{SV-AC-6}{SA-8(16),SA-8(19),SC-3,SC-7(13)}
|
|
|
The [spacecraft] shall initialize the platform to a known safe state.{SA-8(19),SA-8(23),SA-8(24),SI-17}
|
|
|
The [spacecraft] shall maintain the confidentiality and integrity of information during preparation for transmission and during reception in accordance with [organization] provided encryption matrix.{SA-8(19),SC-8,SC-8(1),SC-8(2),SC-8(3)}
|
* Preparation for transmission and during reception includes the aggregation, packing, and transformation options performed prior to transmission and the undoing of those operations that occur upon receipt.
|
|
The [spacecraft] shall implement cryptographic mechanisms that achieve adequate protection against the effects of intentional electromagnetic interference.{SV-AV-1,SV-IT-1}{SA-8(19),SC-8(1),SC-40,SC-40(1)}
|
|
|
The [spacecraft] shall provide the capability to verify the correct operation of security-relevant software and hardware mechanisms (e.g.spacecraft IDS/IPS, logging, crypto, etc..) {SV-DCO-1}{SA-8(21),SI-3,SI-6}
|
|
|
The [organization] shall define and document the transitional state or security-relevant events when the spacecraft will perform integrity checks on software, firmware, and information.{SV-IT-2}{SA-8(21),SI-7(1),SI-7(10),SR-4(4)}
|
|
|
The [spacecraft] shall be capable of removing flight software after updated versions have been installed.{SV-SP-1,SV-SP-9}{SA-8(8),SI-2(6)}
|
|
|
The [spacecraft] shall provide the capability for data connection ports or input/output devices to be disabled or removed prior to spacecraft operations.{SV-AC-5}{SA-9(2),SC-7(14),SC-41,SC-51}
|
Intent is for external physical data ports to be disabled (logical or physical) while in operational orbit. Port disablement does not necessarily need to be irreversible.
|
|
The [spacecraft] shall discriminate between valid and invalid input into the software and rejects invalid input.{SC-16(2),SI-3(8),SI-10,SI-10(3),SI-10(6)}
|
|
|
The [spacecraft] shall identify and reject commands received out-of-sequence when the out-of-sequence commands can cause a hazard/failure or degrade the control of a hazard or mission.{SC-16(2),SI-4(13),SI-4(25),SI-10,SI-10(6),SI-13}
|
|
|
The [spacecraft] shall protect the confidentiality and integrity of the [all information] using cryptography while it is at rest.{SV-IT-2,SV-CF-2}{SC-28,SC-28(1),SI-7(6)}
|
* Information at rest refers to the state of information when it is located on storage devices as specific components of information systems. This is often referred to as data-at-rest encryption.
|
|
The [spacecraft] shall provide independent mission/cyber critical threads such that any one credible event will not corrupt another mission/cyber critical thread.{SC-3,SC-32,SC-32(1),SI-3,SI-13}
|
|
|
The [spacecraft] shall implement protections against external and internal communications from jamming attempts.{SC-5,SC-40,SC-40(1)}
|
|
|
The [spacecraft] shall protect external and internal communications from jamming and spoofing attempts.{SV-AV-1,SV-IT-1}{SC-5,SC-40,SC-40(1)}
|
Can be aided via the Crosslink, S-Band, and L-Band subsystems
|
|
The [organization] shall define the security safeguards to be employed to protect the availability of system resources.{SV-AC-6}{SC-6,SI-17}
|
|
|
The [spacecraft] shall monitor [Program defined telemetry points] for malicious commanding attempts.{SV-AC-1,SV-AC-2}{SC-7,AU-3(1),AC-17(1)}
|
Source from AEROSPACE REPORT NO. TOR-2019-02178
Vehicle Command Counter (VCC) - Counts received valid commands
Rejected Command Counter - Counts received invalid commands
Command Receiver On/Off Mode - Indicates times command receiver is accepting commands
Command Receivers Received Signal Strength - Analog measure of the amount of received RF energy at the receive frequency
Command Receiver Lock Modes - Indicates when command receiver has achieved lock on command signal
Telemetry Downlink Modes - Indicates when the satellite’s telemetry was transmitting
Cryptographic Modes - Indicates the operating modes of the various encrypted links
Received Commands - Log of all commands received and executed by the satellite
System Clock - Master onboard clock
GPS Ephemeris - Indicates satellite location derived from GPS Signals
|
|
The [spacecraft] shall audit the communications characteristics (signals, frequencies, etc.) associated with denied communications.{SC-7(9)}
|
|
|
The [spacecraft] shall implement cryptographic mechanisms to prevent unauthorized disclosure of, and detect changes to, information during transmission unless otherwise protected by alternative physical safeguards.{SV-AC-7}{SC-8(1),SI-7(6)}
|
|
|
The [spacecraft] shall properly handle spurious input and missing data.{SI-10,SI-10(3),SI-10(6)}
|
|
|
The [spacecraft] shall perform prerequisite checks for the execution of hazardous commands.{SI-10,SI-10(6),SI-13}
|
|
|
The [spacecraft] shall validate a functionally independent parameter prior to the issuance of any sequence that could remove an inhibit, or perform a hazardous action.{SI-10(3),SI-10(6),SI-13}
|
|
|
The [spacecraft] shall have failure tolerance on sensors used by software to make mission-critical decisions.{SV-MA-3,SV-AV-7}{SI-13,SI-17}
|
|
|
The [spacecraft] fault management solution shall utilize memory uncorrectable bit error detection information in a strategy to autonomously minimize the adverse effects of uncorrectable bit errors within the spacecraft.{SV-IT-4}{SI-16}
|
|
|
The [spacecraft] Interrupt Service Routine (ISR) shall have the ability to simultaneously update check-bits for [organization]-defined memory addresses.{SV-IT-4}{SI-16}
|
|
|
The [spacecraft] shall integrate EDAC scheme with fault management and cyber-protection mechanisms to respond to the detection of uncorrectable multi-bit errors, other than time-delayed monitoring of EDAC telemetry by the mission operators on the ground.{SV-IT-4}{SI-16}
|
|
|
The [spacecraft] shall use Error Detection and Correcting (EDAC) memory.{SV-IT-4}{SI-16}
|
|
|
The [spacecraft] shall utilize an EDAC scheme to routinely check for bit errors in the stored data on board the spacecraft, correct the single-bit errors, and identify the memory addresses of data with uncorrectable multi-bit errors of at least order two, if not higher order in some cases.{SV-IT-4}{SI-16}
|
|
|
The [spacecraft] cyber-safe mode software/configuration should be stored onboard the spacecraft in memory with hardware-based controls and should not be modifiable.{SV-AV-5,SV-AV-6,SV-AV-7}{SI-17}
|
Cyber-safe mode is using a fail-secure mentality where if there is a malfunction that the spacecraft goes into a fail-secure state where cyber protections like authentication and encryption are still employed (instead of bypassed) and the spacecraft can be restored by authorized commands. The cyber-safe mode should be stored in a high integrity location of the on-board SV so that it cannot be modified by attackers.
|
|
The [spacecraft] shall safely transition between all predefined, known states.{SI-17}
|
|
|
The [spacecraft] software subsystems shall detect and recover/transition from detected memory errors to a known cyber-safe state.{SV-MA-3,SV-AV-7}{SI-17}
|
|
|
The [spacecraft] software subsystems shall initialize the spacecraft to a known safe state.{SV-MA-3,SV-AV-7}{SI-17}
|
|
|
The [spacecraft] software subsystems shall operate securely in off-nominal power conditions, including loss of power and spurious power transients.{SV-MA-3,SV-AV-7}{SI-17}
|
|
|
The [spacecraft] software subsystems shall perform an orderly, controlled system shutdown to a known cyber-safe state upon receipt of a termination command or condition.{SV-MA-3,SV-AV-7}{SI-17}
|
|
|
The [spacecraft] software subsystems shall recover to a known cyber-safe state when an anomaly is detected.{SV-MA-3,SV-AV-7}{SI-17}
|
|
|
The [spacecraft] software subsystems shall safely transition between all predefined, known states.{SV-MA-3,SV-AV-7}{SI-17}
|
|
|
The [spacecraft] shall only use or include critical commands for the purpose of providing emergency access where commanding authority is appropriately restricted.{SI-3(8),SI-10,SI-10(3)}
|
|
|
The [spacecraft] shall monitor all inbound/outbound communications to detect unusual or unauthorized behavior and respond appropriately (disregard command, deny connection, etc.){SI-4(4)}
|
|
|
The [spacecraft] shall perform an integrity check of [Program-defined software, firmware, and information] at startup; at [Program-defined transitional states or security-relevant events] {SV-IT-2}{SI-7(1)}
|
|
|
The [spacecraft] shall automatically [Selection (one or more):restarts the FSW/processor, performs side swap, audits failure; implements Program-defined security safeguards] when integrity violations are discovered.{SV-IT-2}{SI-7(8)}
|
|
|
The [spacecraft] hardware root of trust must be an ECDSA NIST P-384 public key.{SV-IT-3}{SI-7(9)}
|
No requirement is imposed on uniqueness.
|
|
The [spacecraft] hardware root of trust must be loadable only once, post-purchase.{SV-IT-3}{SI-7(9)}
|
No requirement is imposed on preventing hardware readout. The public key belongs to the customer, not the manufacturer, so it must be loaded after purchase. Also, if it can be overwritten, there’s no reason to trust it.
|
|
The [spacecraft] shall implement trusted boot/RoT as a separate compute engine controlling the trusted computing platform cryptographic processor.{SV-IT-3}{SI-7(9)}
|
|
|
The [spacecraft] shall implement trusted boot/RoT computing module on radiation tolerant burn-in (non-programmable) equipment.{SV-IT-3}{SI-7(9)}
|
|
|
The [spacecraft] boot firmware must enter a recovery routine upon failing to verify signed data in the trust chain, and not execute or trust that signed data.{SV-IT-3}{SI-7(9),SI-7(10)}
|
No other requirements are imposed on the recovery routine besides not using the failed data. Unverifiable data isn’t trusted and shouldn’t be run.
|
|
The [spacecraft] root of trust must be an ECDSA NIST P-384 public key.{SI-7(9),SI-7(10)}
|
|
|
The [spacecraft] root of trust must be loadable only once, post-purchase.{SI-7(9),SI-7(10)}
|
|
|
The [spacecraft] secure boot mechanism shall be Commercial National Security Algorithm Suite (CNSA) compliant.{SV-IT-3}{SI-7(9),SI-7(10)}
|
No certification process is required (or exists). The CNSA is easy to meet, only restricts algorithm choice, and aids ease-of-use for government customers.
|
|
The [spacecraft] shall allocate enough boot ROM memory for secure boot firmware execution.{SV-IT-3}{SI-7(9),SI-7(10)}
|
|
|
The [spacecraft] shall allocate enough SRAM memory for secure boot firmware execution.{SV-IT-3}{SI-7(9),SI-7(10)}
|
|
|
The [spacecraft] shall support the algorithmic construct of Elliptic Curve Digital Signature Algorithm (ECDSA) NIST P-384 + SHA-38 or equivalent strength.{SV-IT-3}{SI-7(9),SI-7(10)}
|
Timing data may suggest cryptographic accelerators are unnecessary. This construct was chosen because (a) it’s in the CNSA suite and (b) it doesn’t require secret values to be stored
|
|
The [spacecraft] shall implement the hardware, firmware, and software anti-tamper mechanisms identified in the Anti-Tamper Plan.{SR-9(1),SR-10}
|
|