Inject Malicious Code

Threat actors may rely on other tactics and techniques in order to inject malicious code into the victim spacecraft. This can be done via compromising the supply chain or development environment in some capacity or taking advantage of known commands. However, once malicious code has been uploaded to the victim spacecraft, the threat actor can then trigger the code to run via a specific command or wait for a legitimate user to trigger it accidently. The code itself can do a number of different things to the hosted payload, subsystems, or underlying OS.

ID: CM0044
Sub-techniques: 
Related Aerospace Threat IDs:  SV-SP-3 SV-SP-6 SV-SP-7 SV-SP-9
Related MITRE ATT&CK TTPs:  T1204.002
Tactic:
Created: 2022/10/19
Last Modified: 2022/12/08

Countermeasures

ID Name Description NIST Rev5 D3FEND ISO 27001
CM0020 Threat modeling Use threat modeling and vulnerability analysis to inform the current development process using analysis from similar systems, components, or services where applicable. SA-11(2) SA-15(8)
CM0011 Vulnerability Scanning Vulnerability scanning is used to identify known software vulnerabilities (excluding custom-developed software - ex: COTS and Open-Source). Utilize scanning tools to identify vulnerabilities in dependencies and outdated software (i.e., software composition analysis). Ensure that vulnerability scanning tools and techniques are employed that facilitate interoperability among tools and automate parts of the vulnerability management process by using standards for: (1) Enumerating platforms, custom software flaws, and improper configurations; (2) Formatting checklists and test procedures; and (3) Measuring vulnerability impact. CM-10(1) RA-5 RA-5(11) RA-5(3) SA-15(7) SI-3 A.8.8 A.8.7
CM0012 Software Bill of Materials Generate Software Bill of Materials (SBOM) against the entire software supply chain and cross correlate with known vulnerabilities (e.g., Common Vulnerabilities and Exposures) to mitigate known vulnerabilities. Protect the SBOM according to countermeasures in CM0001. CM-10(1) CM-11(3) CM-8 CM-8(7) RA-5(11) SA-10(4) A.5.9 A.8.9
CM0015 Software Source Control Prohibit the use of binary or machine-executable code from sources with limited or no warranty and without the provision of source code. CM-14 CM-7(8) SA-10(4)
CM0016 CWE List Create prioritized list of software weakness classes (e.g., Common Weakness Enumerations), based on system-specific considerations, to be used during static code analysis for prioritization of static analysis results. RA-5 SA-11(1) SA-15(7) A.8.8 A.8.28
CM0017 Coding Standard Define acceptable coding standards to be used by the software developer. The mission should have automated means to evaluate adherence to coding standards. The coding standard should include the acceptable software development language types as well. The language should consider the security requirements, scalability of the application, the complexity of the application, development budget, development time limit, application security, available resources, etc. The coding standard and language choice must ensure proper security constructs are in place. SA-15 A.5.8 A.8.25
CM0018 Dynamic Analysis Employ dynamic analysis (e.g., using simulation, penetration testing, fuzzing, etc.) to identify software/firmware weaknesses and vulnerabilities in developed and incorporated code (open source, commercial, or third-party developed code). Testing should occur (1) on potential system elements before acceptance; (2) as a realistic simulation of known adversary tactics, techniques, procedures (TTPs), and tools; and (3) throughout the lifecycle on physical and logical systems, elements, and processes. FLATSATs as well as digital twins can be used to perform the dynamic analysis depending on the TTPs being executed. Digital twins via instruction set simulation (i.e., emulation) can provide robust environment for dynamic analysis and TTP execution. CA-8 CP-4(5) RA-5(11) SA-11(5) SA-11(8) SA-11(9) SC-2(2) SC-7(29) SI-3 SR-6(1) SR-6(1) A.8.7
CM0019 Static Analysis Perform static source code analysis for all available source code looking for system-relevant weaknesses (see CM0016) using no less than two static code analysis tools. RA-5 SA-11(1) SA-15(7) A.8.8 A.8.28
CM0047 Operating System Security Ensure spacecraft's operating system is scrutinized/whitelisted and has received adequate software assurance previously. The operating system should be analyzed for its attack surface and non-utilized features should be stripped from the operating system. Many real-time operating systems contain features that are not necessary for spacecraft operations and only increase the attack surface. CM-11(3) CM-7 CM-7(5) CM-7(8) CM-7(8) SI-3(8) A.8.19 A.8.19
CM0069 Process White Listing Simple process ID whitelisting on the firmware level could impede attackers from instigating unnecessary processes which could impact the spacecraft CM-7(5) SI-10(5) A.8.19
CM0032 On-board Intrusion Detection & Prevention Utilize on-board intrusion detection/prevention system that monitors the mission critical components or systems and audit/logs actions. The IDS/IPS should have the capability to respond to threats (initial access, execution, persistence, evasion, exfiltration, etc.) and it should address signature-based attacks along with dynamic never-before seen attacks using machine learning/adaptive technologies. The IDS/IPS must integrate with traditional fault management to provide a wholistic approach to faults on-board the spacecraft. Spacecraft should select and execute safe countermeasures against cyber-attacks.  These countermeasures are a ready supply of options to triage against the specific types of attack and mission priorities. Minimally, the response should ensure vehicle safety and continued operations. Ideally, the goal is to trap the threat, convince the threat that it is successful, and trace and track the attacker — with or without ground support. This would support successful attribution and evolving countermeasures to mitigate the threat in the future. “Safe countermeasures” are those that are compatible with the system’s fault management system to avoid unintended effects or fratricide on the system. AU-14 AU-2 AU-3 AU-3(1) AU-4 AU-4(1) AU-5 AU-5(2) AU-5(5) AU-6(1) AU-6(4) AU-8 AU-9 AU-9(2) AU-9(3) CA-7(6) CM-11(3) CP-10 CP-10(4) IR-4 IR-4(11) IR-4(12) IR-4(14) IR-4(5) IR-5 IR-5(1) RA-10 RA-3(4) SA-8(21) SA-8(22) SA-8(23) SC-16(2) SC-32(1) SC-5 SC-5(3) SC-7(10) SC-7(9) SI-10(6) SI-16 SI-17 SI-3 SI-3(8) SI-4 SI-4(1) SI-4(10) SI-4(11) SI-4(13) SI-4(16) SI-4(17) SI-4(2) SI-4(23) SI-4(24) SI-4(25) SI-4(4) SI-4(5) SI-6 SI-7(17) SI-7(8) A.8.15 A.8.15 A.8.6 A.8.17 A.5.33 A.8.15 A.8.15 A.5.29 A.5.25 A.5.26 A.5.27 A.5.7 A.8.12 A.8.7 A.8.16 A.8.16 A.8.16 A.8.16
CM0042 Robust Fault Management Ensure fault management system cannot be used against the spacecraft. Examples include: safe mode with crypto bypass, orbit correction maneuvers, affecting integrity of telemetry to cause action from ground, or some sort of proximity operation to cause spacecraft to go into safe mode. Understanding the safing procedures and ensuring they do not put the spacecraft in a more vulnerable state is key to building a resilient spacecraft. CP-4(5) SA-8(24) SC-16(2) SC-24 SC-5 SI-13 SI-17
CM0044 Cyber-safe Mode Provide the capability to enter the spacecraft into a configuration-controlled and integrity-protected state representing a known, operational cyber-safe state (e.g., cyber-safe mode). Spacecraft should enter a cyber-safe mode when conditions that threaten the platform are detected.   Cyber-safe mode is an operating mode of a spacecraft during which all nonessential systems are shut down and the spacecraft is placed in a known good state using validated software and configuration settings. Within cyber-safe mode, authentication and encryption should still be enabled. The spacecraft should be capable of reconstituting firmware and software functions to pre-attack levels to allow for the recovery of functional capabilities. This can be performed by self-healing, or the healing can be aided from the ground. However, the spacecraft needs to have the capability to replan, based on equipment still available after a cyber-attack. The goal is for the spacecraft to resume full mission operations. If not possible, a reduced level of mission capability should be achieved. Cyber-safe mode software/configuration should be stored onboard the spacecraft in memory with hardware-based controls and should not be modifiable.                                                  CP-10 CP-10(4) CP-12 CP-2(5) IR-4 IR-4(12) IR-4(3) SA-8(21) SA-8(23) SA-8(24) SC-16(2) SC-24 SC-5 SI-11 SI-17 SI-7(17) A.5.29 A.5.25 A.5.26 A.5.27

References