Check the validity of the following information inputs: [Assignment: organization-defined information inputs to the system].
ID | Name | Description | D3FEND | |
CM0002 | COMSEC | Utilizing secure communication protocols with strong cryptographic mechanisms to prevent unauthorized disclosure of, and detect changes to, information during transmission. Systems should also maintain the confidentiality and integrity of information during preparation for transmission and during reception. Spacecraft should not employ a mode of operations where cryptography on the TT&C link can be disabled (i.e., crypto-bypass mode). The cryptographic mechanisms should identify and reject wireless transmissions that are deliberate attempts to achieve imitative or manipulative communications deception based on signal parameters. | ||
CM0033 | Relay Protection | Implement relay and replay-resistant authentication mechanisms for establishing a remote connection or connections on the spacecraft bus. | ||
CM0005 | Ground-based Countermeasures | This countermeasure is focused on the protection of terrestrial assets like ground networks and development environments/contractor networks, etc. Traditional detection technologies and capabilities would be applicable here. Utilizing resources from NIST CSF to properly secure these environments using identify, protect, detect, recover, and respond is likely warranted. Additionally, NISTIR 8401 may provide resources as well since it was developed to focus on ground-based security for space systems (https://nvlpubs.nist.gov/nistpubs/ir/2022/NIST.IR.8401.ipd.pdf). Furthermore, the MITRE ATT&CK framework provides IT focused TTPs and their mitigations https://attack.mitre.org/mitigations/enterprise/. Several recommended NIST 800-53 Rev5 controls are provided for reference when designing ground systems/networks. | ||
CM0043 | Backdoor Commands | Ensure that all viable commands are known to the mission/spacecraft owner. Perform analysis of critical (backdoor/hardware) commands that could adversely affect mission success if used maliciously. Only use or include critical commands for the purpose of providing emergency access where commanding authority is appropriately restricted. |
ID | Description | |
SV-IT-2 |
Unauthorized modification or corruption of data |
|
SV-MA-3 |
Attacks on critical software subsystems Attitude Determination and Control (AD&C) subsystem determines and controls the orientation of the satellite. Any cyberattack that could disrupt some portion of the control loop - sensor data, computation of control commands, and receipt of the commands would impact operations Telemetry, Tracking and Commanding (TT&C) subsystem provides interface between satellite and ground system. Computations occur within the RF portion of the TT&C subsystem, presenting cyberattack vector Command and Data Handling (C&DH) subsystem is the brains of the satellite. It interfaces with other subsystems, the payload, and the ground. It receives, validate, decodes, and sends commands to other subsystems, and it receives, processes, formats, and routes data for both the ground and onboard computer. C&DH has the most cyber content and is likely the biggest target for cyberattack. Electrical Power Subsystem (EPS) provides, stores, distributes, and controls power on the satellite. An attack on EPS could disrupt, damage, or destroy the satellite. |
|
SV-SP-1 |
Exploitation of software vulnerabilities (bugs); Unsecure code, logic errors, etc. in the FSW. |
|
SV-SP-6 |
Software reuse, COTS dependence, and standardization of onboard systems using building block approach with addition of open-source technology leads to supply chain threat |
|
SV-AC-5 |
Proximity operations (i.e., grappling satellite) |
|
SV-AC-6 |
Three main parts of S/C. CPU, memory, I/O interfaces with parallel and/or serial ports. These are connected via busses (i.e., 1553) and need segregated. Supply chain attack on CPU (FPGA/ASICs), supply chain attack to get malware burned into memory through the development process, and rogue RTs on 1553 bus via hosted payloads are all threats. Security or fault management being disabled by non-mission critical or payload; fault injection or MiTM into the 1553 Bus - China has developed fault injector for 1553 - this could be a hosted payload attack if payload has access to main 1553 bus; One piece of FSW affecting another. Things are not containerized from the OS or FSW perspective; |
|
SV-AC-8 |
Malicious Use of hardware commands - backdoors / critical commands |
|
SV-SP-7 |
Software can be broken down into three levels (operating system and drivers’ layer, data handling service layer, and the application layer). Highest impact on system is likely the embedded code at the BIOS, kernel/firmware level. Attacking the on-board operating systems. Since it manages all the programs and applications on the computer, it has a critical role in the overall security of the system. Since threats may occur deliberately or due to human error, malicious programs or persons, or existing system vulnerability mitigations must be deployed to protect the OS. |
|
SV-AC-1 |
Attempting access to an access-controlled system resulting in unauthorized access |
|
SV-AC-2 |
Replay of recorded authentic communications traffic at a later time with the hope that the authorized communications will provide data or some other system reaction |
|
SV-IT-1 |
Communications system spoofing resulting in denial of service and loss of availability and data integrity |
|
SV-AC-7 |
Weak communication protocols. Ones that don't have strong encryption within it |
|
SV-AV-1 |
Communications system jamming resulting in denial of service and loss of availability and data integrity |
|
SV-MA-7 |
Exploit ground system and use to maliciously to interact with the spacecraft |
|
SV-AC-4 |
Masquerading as an authorized entity in order to gain access/Insider Threat |
|
SV-AV-7 |
The TT&C is the lead contributor to satellite failure over the first 10 years on-orbit, around 20% of the time. The failures due to gyro are around 12% between year one and 6 on-orbit and then ramp up starting around year six and overtake the contributions of the TT&C subsystem to satellite failure. Need to ensure equipment is not counterfeit and the supply chain is sound. |
|
SV-MA-6 |
Not planning for security on SV or designing in security from the beginning |
Requirement | Rationale/Additional Guidance/Notes |
---|---|
The [organization] shall protect the security plan from unauthorized disclosure and modification.{SV-MA-6}{AC-3,PL-2,PL-7} | |
The [organization] shall identify the key system components or capabilities that require isolation through physical or logical means.{SV-AC-6}{AC-3,SC-3,SC-7(13),SC-28(3),SC-32,SC-32(1)} | Fault management and security management capabilities would be classified as mission critical and likely need separated. Additionally, capabilities like TT&C, C&DH, GNC might need separated as well. |
The [organization] shall implement a verifiable flaw remediation process into the developmental and operational configuration management process.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CA-2,CA-5,SA-3,SA-3(1),SA-11,SI-3,SI-3(10)} | The verifiable process should also include a cross reference to mission objectives and impact statements. Understanding the flaws discovered and how they correlate to mission objectives will aid in prioritization. |
The [organization] shall verify that the scope of security testing/evaluation provides complete coverage of required security controls (to include abuse cases and penetration testing) at the depth of testing defined in the test documents.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CA-2,CA-8,RA-5(3),SA-11(5),SA-11(7)} | * The frequency of testing should be driven by Program completion events and updates. * Examples of approaches are static analyses, dynamic analyses, binary analysis, or a hybrid of the three approaches |
The [organization] shall maintain evidence of the execution of the security assessment plan and the results of the security testing/evaluation.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CA-2,CA-8,SA-11} | |
The [organization] shall create and implement a security assessment plan that includes: (1) The types of analyses, testing, evaluation, and reviews of all software and firmware components; (2) The degree of rigor to be applied to include abuse cases and/or penetration testing; and (3) The types of artifacts produced during those processes.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CA-2,CA-8,SA-11,SA-11(5)} | The security assessment plan should include evaluation of mission objectives in relation to the security of the mission. Assessments should not only be control based but also functional based to ensure mission is resilient against failures of controls. |
The [organization] shall determine the vulnerabilities/weaknesses that require remediation, and coordinate the timeline for that remediation, in accordance with the analysis of the vulnerability scan report, the mission assessment of risk, and mission needs.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CA-5,CM-3,RA-5,RA-7,SI-3,SI-3(10)} | |
The [organization] shall employ dynamic analysis (e.g.using simulation, penetration testing, fuzzing, etc.) to identify software/firmware weaknesses and vulnerabilities in developed and incorporated code (open source, commercial, or third-party developed code).{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CA-8,CM-10(1),RA-3(1),SA-11(5),SA-11(8),SA-11(9),SI-3,SI-7(10)} | |
The [organization] shall perform penetration testing/analysis: (1) On potential system elements before accepting the system; (2) As a realistic simulation of the active adversary’s known adversary tactics, techniques, procedures (TTPs), and tools; and (3) Throughout the lifecycle on physical and logical systems, elements, and processes.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{CA-8(1),SA-9,SA-11(5),SR-5(2)} | Penetration testing should be performed throughout the lifecycle on physical and logical systems, elements, and processes including: (1) Hardware, software, and firmware development processes; (2) Shipping/handling procedures; (3) Personnel and physical security programs; (4) Configuration management tools/measures to maintain provenance; and (5) Any other programs, processes, or procedures associated with the production/distribution of supply chain elements. |
The [organization] shall test software and firmware updates related to flaw remediation for effectiveness and potential side effects on mission systems in a separate test environment before installation.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CM-3,CM-3(1),CM-3(2),CM-4(1),CM-4(2),CM-10(1),SA-8(31),SA-11(9),SI-2,SI-3,SI-3(10),SI-7(10),SI-7(12),SR-5(2)} | This requirement is focused on software and firmware flaws. If hardware flaw remediation is required, refine the requirement to make this clear. |
The [organization] shall define processes and procedures to be followed when integrity verification tools detect unauthorized changes to software, firmware, and information.{SV-IT-2}{CM-3,CM-3(1),CM-3(5),CM-5(6),CM-6,CP-2,IR-6,IR-6(2),PM-30,SC-16(1),SC-51,SI-3,SI-4(7),SI-4(24),SI-7,SI-7(7),SI-7(10)} | |
The [organization] shall release updated versions of the mission information systems incorporating security-relevant software and firmware updates, after suitable regression testing, at a frequency no greater than [Program-defined frequency [90 days]].{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CM-3(2),CM-4(1)} | On-orbit patching/upgrades may be necessary if vulnerabilities are discovered after launch. The system should have the ability to update software post-launch. |
The [organization] shall develop and implement anti-counterfeit policy and procedures designed to detect and prevent counterfeit components from entering the information system, including support tamper resistance and provide a level of protection against the introduction of malicious code or hardware.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{CM-3(8),CM-7(9),PM-30,SA-8(9),SA-8(11),SA-9,SA-10(3),SA-19,SC-51,SR-4(3),SR-4(4),SR-5(2),SR-11} | |
The [organization] shall define/maintain an approved operating system list for use on spacecraft.{SV-SP-7}{CM-7(5)} | The operating system is extremely important to security and availability of the spacecraft, therefore should receive high levels of assurance that it operates as intended and free of critical weaknesses/vulnerabilities. |
The [organization] shall prohibit the use of binary or machine-executable code from sources with limited or no warranty and without the provision of source code.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{CM-7(8)} | |
The [organization] shall conduct a criticality analysis to identify mission critical functions and critical components and reduce the vulnerability of such functions and components through secure system design.{SV-SP-3,SV-SP-4,SV-AV-7,SV-MA-4}{CP-2,CP-2(8),PL-7,PM-11,PM-30(1),RA-3(1),RA-9,SA-8(9),SA-8(11),SA-8(25),SA-12,SA-14,SA-15(3),SC-7(29),SR-1} | During SCRM, criticality analysis will aid in determining supply chain risk. For mission critical functions/components, extra scrutiny must be applied to ensure supply chain is secured. |
The [organization] shall define policy and procedures to ensure that the developed or delivered systems do not embed unencrypted static authenticators in applications, access scripts, configuration files, nor store unencrypted static authenticators on function keys.{SV-AC-1,SV-AC-3}{IA-5(7)} | |
The [organization] shall report identified systems or system components containing software affected by recently announced cybersecurity-related software flaws (and potential vulnerabilities resulting from those flaws) to [organization] officials with cybersecurity responsibilities.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-11}{IR-6,IR-6(2),SI-2,SI-3,SI-4(12),SR-4(4)} | |
The [organization] shall have a two-man rule to achieve a high level of security for systems with command level access to the spacecraft.(Under this rule all access and actions require the presence of two authorized people at all times.) {SV-AC-4}{PE-3} | Note: These are not spacecraft requirements but important to call out but likely are covered under other requirements by the customer. |
The [organization] shall plan and coordinate security-related activities affecting the spacecraft with groups associated with systems from which the spacecraft is inheriting satisfaction of controls before conducting such activities in order to reduce the impact on other organizational entities.{SV-MA-6}{PL-2} | |
The [organization] shall develop a security plan for the spacecraft.{SV-MA-6}{PL-2,PL-7,PM-1,SA-8(29),SA-8(30)} | |
The [organization] shall have Insider Threat Program to aid in the prevention of people with authorized access to perform malicious activities.{SV-AC-4}{PM-12,AT-2(2),IR-4(7)} | Note: These are not spacecraft requirements but important to call out but likely are covered under other requirements by the customer. |
The [organization] shall use all-source intelligence analysis of suppliers and potential suppliers of the information system, system components, or system services to inform engineering, acquisition, and risk management decisions.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{PM-16,PM-30,RA-2,RA-3(1),RA-3(2),RA-7,SA-9,SA-12(8),SR-5(2)} | * The Program should also consider sub suppliers and potential sub suppliers. * All-source intelligence of suppliers that the organization may use includes: (1) Defense Intelligence Agency (DIA) Threat Assessment Center (TAC), the enterprise focal point for supplier threat assessments for the DOD acquisition community risks; (2) Other U.S. Government resources including: (a) Government Industry Data Exchange Program (GIDEP) – Database where government and industry can record issues with suppliers, including counterfeits; and (b) System for Award Management (SAM) – Database of companies that are barred from doing business with the US Government. |
The [organization] shall maintain documentation tracing the strategies, tools, and methods implemented to mitigate supply chain risk .{SV-SP-3,SV-SP-4,SV-AV-7}{PM-30,RA-3(1),SA-12(1),SR-5} | Examples include: (1) Transferring a portion of the risk to the developer or supplier through the use of contract language and incentives; (2) Using contract language that requires the implementation of SCRM throughout the system lifecycle in applicable contracts and other acquisition and assistance instruments (grants, cooperative agreements, Cooperative Research and Development Agreements (CRADAs), and other transactions). Within the DOD some examples include: (a) Language outlined in the Defense Acquisition Guidebook section 13.13. Contracting; (b) Language requiring the use of protected mechanisms to deliver elements and data about elements, processes, and delivery mechanisms; (c) Language that articulates that requirements flow down supply chain tiers to sub-prime suppliers. (3) Incentives for suppliers that: (a) Implement required security safeguards and SCRM best practices; (b) Promote transparency into their organizational processes and security practices; (c) Provide additional vetting of the processes and security practices of subordinate suppliers, critical information system components, and services; and (d) Implement contract to reduce SC risk down the contract stack. (4) Gaining insight into supplier security practices; (5) Using contract language and incentives to enable more robust risk management later in the lifecycle; (6) Using a centralized intermediary or “Blind Buy” approaches to acquire element(s) to hide actual usage locations from an untrustworthy supplier or adversary; |
The [organization] shall protect against supply chain threats to the system, system components, or system services by employing security safeguards as defined by NIST SP 800-161 Rev.1.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{PM-30,RA-3(1),SA-8(9),SA-8(11),SA-12,SI-3,SR-1} | The chosen supply chain safeguards should demonstrably support a comprehensive, defense-in-breadth information security strategy. Safeguards should include protections for both hardware and software. Program should define their critical components (HW & SW) and identify the supply chain protections, approach/posture/process. |
The [organization], upon termination of individual employment, disables information system access within [TBD minutes] of termination.{SV-AC-4}{PS-4} | |
The [organization] shall use the threat and vulnerability analyses of the as-built system, system components, or system services to inform and direct subsequent testing/evaluation of the as-built system, component, or service.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{RA-3(3),SA-11(2),SA-15(8),SI-3} | |
The [organization] shall share information obtained from the vulnerability scanning process and security control assessments with [Program-defined personnel or roles] to help eliminate similar vulnerabilities in other systems (i.e., systemic weaknesses or deficiencies).{SV-SP-1}{RA-5} | |
The [organization] shall ensure that the vulnerability scanning tools (e.g., static analysis and/or component analysis tools) used include the capability to readily update the list of potential information system vulnerabilities to be scanned.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{RA-5,RA-5(1),RA-5(3),SI-3} | |
The [organization] shall perform vulnerability analysis and risk assessment of all systems and software.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{RA-5,RA-5(3),SA-15(7),SI-3} | |
The [organization] shall ensure that vulnerability scanning tools and techniques are employed that facilitate interoperability among tools and automate parts of the vulnerability management process by using standards for: (1) Enumerating platforms, custom software flaws, and improper configurations; (2) Formatting checklists and test procedures; and (3) Measuring vulnerability impact.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{RA-5,RA-5(3),SI-3} | Component/Origin scanning looks for open-source libraries/software that may be included into the baseline and looks for known vulnerabilities and open-source license violations. |
The [organization] shall perform static binary analysis of all firmware that is utilized on the spacecraft.{SV-SP-7,SV-SP-11}{RA-5,SA-10,SA-11,SI-7(10)} | Many commercial products/parts are utilized within the system and should be analyzed for security weaknesses. Blindly accepting the firmware is free of weakness is unacceptable for high assurance missions. The intent is to not blindly accept firmware from unknown sources and assume it is secure. This is meant to apply to firmware the vendors are not developing internally. In-house developed firmware should be going through the vendor's own testing program and have high assurance it is secure. When utilizing firmware from other sources, "expecting" does not meet this requirement. Each supplier needs to provide evidence to support that claim that their firmware they are getting is genuine and secure. |
The [organization] shall perform static source code analysis for all available source code looking for [[organization]-defined Top CWE List] weaknesses using complimentary set of static code analysis tools (i.e.more than one).{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{RA-5,SA-11(1),SA-15(7)} | |
The [organization] shall analyze vulnerability/weakness scan reports and results from security control assessments.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{RA-5,SI-3} | |
The [organization] shall ensure that the list of potential system vulnerabilities scanned is updated [prior to a new scan] {SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{RA-5(2),SI-3} | |
The [organization] shall perform configuration management during system, component, or service during [design; development; implementation; operations].{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-10} | |
The [organization] shall review proposed changes to the spacecraft, assessing both mission and security impacts.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-10,CM-3(2)} | |
The [organization] shall correct flaws identified during security testing/evaluation.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-11} | Flaws that impact the mission objectives should be prioritized. |
The [organization] shall perform [Selection (one or more): unit; integration; system; regression] testing/evaluation at [Program-defined depth and coverage].{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-11} | The depth needs to include functional testing as well as negative/abuse testing. |
The [organization] shall create prioritized list of software weakness classes (e.g., Common Weakness Enumerations) to be used during static code analysis for prioritization of static analysis results.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-11(1),SA-15(7)} | The prioritized list of CWEs should be created considering operational environment, attack surface, etc. Results from the threat modeling and attack surface analysis should be used as inputs into the CWE prioritization process. There is also a CWSS (https://cwe.mitre.org/cwss/cwss_v1.0.1.html) process that can be used to prioritize CWEs. The prioritized list of CWEs can help with tools selection as well as you select tools based on their ability to detect certain high priority CWEs. |
The [organization] shall use threat modeling and vulnerability analysis to inform the current development process using analysis from similar systems, components, or services where applicable.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-11(2),SA-15(8)} | |
The [organization] shall perform and document threat and vulnerability analyses of the as-built system, system components, or system services.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-11(2),SI-3} | |
The [organization] shall perform a manual code review of all flight code.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-11(4)} | |
The [organization] shall conduct an Attack Surface Analysis and reduce attack surfaces to a level that presents a low level of compromise by an attacker.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-11(6),SA-15(5)} | |
The [organization] shall define acceptable coding languages to be used by the software developer.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-15} | |
The [organization] shall define acceptable secure coding standards for use by the software developers.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-15} | |
The [organization] shall have automated means to evaluate adherence to coding standards.{SV-SP-1,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-15,SA-15(7),RA-5} | Manual review cannot scale across the code base; you must have a way to scale in order to confirm your coding standards are being met. The intent is for automated means to ensure code adheres to a coding standard. |
The [organization] shall perform component analysis (a.k.a.origin analysis) for developed or acquired software.{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SA-15(7),RA-5} | |
The [organization] shall document the spacecraft's security architecture, and how it is established within and is an integrated part of the Program's mission security architecture.{SV-MA-6}{SA-17} | |
The [organization] shall require subcontractors developing information system components or providing information system services (as appropriate) to demonstrate the use of a system development life cycle that includes [state-of-the-practice system/security engineering methods, software development methods, testing/evaluation/validation techniques, and quality control processes].{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-9}{SA-3,SA-4(3)} | Select the particular subcontractors, software vendors, and manufacturers based on the criticality analysis performed for the Program Protection Plan and the criticality of the components that they supply. |
The [organization] shall require the developer of the system, system component, or system service to deliver the system, component, or service with [Program-defined security configurations] implemented.{SV-SP-1,SV-SP-9}{SA-4(5)} | For the spacecraft FSW, the defined security configuration could include to ensure the software does not contain a pre-defined list of Common Weakness Enumerations (CWEs)and/or CAT I/II Application STIGs. |
The [organization] shall perform analysis of critical backdoor commands that could adversely affect mission success if used maliciously.{SI-10,SI-10(3)} | |
The [organization] shall correct reported cybersecurity-related information system flaws.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SI-2} | * Although this requirement is stated to specifically apply to cybersecurity-related flaws, the Program office may choose to broaden it to all SV flaws. * This requirement is allocated to the Program, as it is presumed, they have the greatest knowledge of the components of the system and when identified flaws apply. |
The [organization] shall identify, report, and coordinate correction of cybersecurity-related information system flaws.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-7,SV-SP-9,SV-SP-11}{SI-2} | |
The [organization] shall employ [organization]-defined techniques to limit harm from potential adversaries identifying and targeting the Program supply chain.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{SR-3(2),SC-38} | Examples of security safeguards that the organization should consider implementing to limit the harm from potential adversaries targeting the organizational supply chain, are: (1) Using trusted physical delivery mechanisms that do not permit access to the element during delivery (ship via a protected carrier, use cleared/official couriers, or a diplomatic pouch); (2) Using trusted electronic delivery of products and services (require downloading from approved, verification-enhanced sites); (3) Avoiding the purchase of custom configurations, where feasible; (4) Using procurement carve outs (i.e., exclusions to commitments or obligations), where feasible; (5) Using defensive design approaches; (6) Employing system OPSEC principles; (7) Employing a diverse set of suppliers; (8) Employing approved vendor lists with standing reputations in industry; (9) Using a centralized intermediary and “Blind Buy” approaches to acquire element(s) to hide actual usage locations from an untrustworthy supplier or adversary Employing inventory management policies and processes; (10) Using flexible agreements during each acquisition and procurement phase so that it is possible to meet emerging needs or requirements to address supply chain risk without requiring complete revision or re-competition of an acquisition or procurement; (11) Using international, national, commercial or government standards to increase potential supply base; (12) Limiting the disclosure of information that can become publicly available; and (13) Minimizing the time between purchase decisions and required delivery. |
The [organization] shall employ the [organization]-defined approaches for the purchase of the system, system components, or system services from suppliers.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{SR-5} | This could include tailored acquisition strategies, contract tools, and procurement methods. |
The [organization] (and Prime Contractor) shall conduct a supplier review prior to entering into a contractual agreement with a contractor (or sub-contractor) to acquire systems, system components, or system services.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{SR-6} | |
The [organization] shall employ [Selection (one or more): independent third-party analysis, Program penetration testing, independent third-party penetration testing] of [Program-defined supply chain elements, processes, and actors] associated with the system, system components, or system services.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{SR-6(1)} | |
The [organization] shall employ [Program-defined Operations Security (OPSEC) safeguards] to protect supply chain-related information for the system, system components, or system services.{SV-SP-3,SV-SP-4,SV-AV-7,SV-SP-11}{SR-7,SC-38,CP-2(8)} | OPSEC safeguards may include: (1) Limiting the disclosure of information needed to design, develop, test, produce, deliver, and support the element for example, supplier identities, supplier processes, potential suppliers, security requirements, design specifications, testing and evaluation result, and system/component configurations, including the use of direct shipping, blind buys, etc.; (2) Extending supply chain awareness, education, and training for suppliers, intermediate users, and end users; (3) Extending the range of OPSEC tactics, techniques, and procedures to potential suppliers, contracted suppliers, or sub-prime contractor tier of suppliers; and (4) Using centralized support and maintenance services to minimize direct interactions between end users and original suppliers. |
The [organization] shall enable integrity verification of software and firmware components.{SV-IT-2}{CM-3(5),CM-5(6),CM-10(1),SA-8(9),SA-8(11),SA-8(21),SA-10(1),SI-3,SI-4(24),SI-7,SI-7(10),SI-7(12),SR-4(4)} | * The integrity verification mechanisms may include: ** Stipulating and monitoring logical delivery of products and services, requiring downloading from approved, verification-enhanced sites; ** Encrypting elements (software, software patches, etc.) and supply chain process data in transit (motion) and at rest throughout delivery; ** Requiring suppliers to provide their elements “secure by default”, so that additional configuration is required to make the element insecure; ** Implementing software designs using programming languages and tools that reduce the likelihood of weaknesses; ** Implementing cryptographic hash verification; and ** Establishing performance and sub-element baseline for the system and system elements to help detect unauthorized tampering/modification during repairs/refurbishing. ** Stipulating and monitoring logical delivery of products and services, requiring downloading from approved, verification-enhanced sites; ** Encrypting elements (software, software patches, etc.) and supply chain process data in transit (motion) and at rest throughout delivery; ** Requiring suppliers to provide their elements “secure by default”, so that additional configuration is required to make the element insecure; ** Implementing software designs using programming languages and tools that reduce the likelihood of weaknesses; ** Implementing cryptographic hash verification; and ** Establishing performance and sub-element baseline for the system and system elements to help detect unauthorized tampering/modification during repairs/refurbishing. |
The [organization] shall have physical security controls to prevent unauthorized access to the systems that have the ability to command the spacecraft.{SV-AC-4}{PE-3} | Note: These are not spacecraft requirements but important to call out but likely are covered under other requirements by the customer. |
The [organization] shall require the developer of the system, system component, or system services to demonstrate the use of a system development life cycle that includes [state-of-the-practice system/security engineering methods, software development methods, testing/evaluation/validation techniques, and quality control processes].{SV-SP-1,SV-SP-2,SV-SP-3,SV-SP-9}{SA-3,SA-4(3)} | Examples of good security practices would be using defense-in-depth tactics across the board, least-privilege being implemented, two factor authentication everywhere possible, using DevSecOps, implementing and validating adherence to secure coding standards, performing static code analysis, component/origin analysis for open source, fuzzing/dynamic analysis with abuse cases, etc. |
The [organization] should have requirements/controls for all ground/terrestrial systems covering: Data Protection, Ground Software, Endpoints, Networks, Computer Network Defense / Incident Response, Perimeter Security, Physical Controls, and Prevention Program (SSP, PPP, and Training).See NIST 800-53 and CNSSI 1253 for guidance on ground security {SV-MA-7} | |
The [spacecraft] shall terminate the connection associated with a communications session at the end of the session or after 3 minutes of inactivity.{SV-AC-1}{AC-12,SA-8(18),SC-10,SC-23(1),SC-23(3),SI-14,SI-14(3)} | |
The [organization] shall ensure reused TT&C software has adequate uniqueness for command decoders/dictionaries so that commands are received by only the intended satellite.{SV-SP-6}{AC-17(10),SC-16(3),SI-3(9)} | The goal is to eliminate risk that compromise of one command database does not affect a different one due to reuse. The intent is to ensure that one SV can not process the commands from another SV. Given the crypto setup with keys and VCC needing to match, this requirement may be inherently met as a result of using type-1 cryptography. The intent is not to recreate entire command dictionaries but have enough uniqueness in place that it prevents a SV from receiving a rogue command. As long as there is some uniqueness at the receiving end of the commands, that is adequate. |
The [spacecraft] shall accept hazardous commands only when prerequisite checks are satisfied.{AC-17(4),SI-10,SI-10(6)} | |
The [spacecraft] shall protect authenticator content from unauthorized disclosure and modification.{SV-AC-1,SV-AC-3}{AC-17(6),CM-3(6),IA-5,IA-5(6),RA-5(4),SA-8(18),SA-8(19),SC-28(3)} | |
The [spacecraft] encryption key handling shall be handled outside of the onboard software and protected using cryptography.{SV-AC-1,SV-AC-3}{AC-17(6),CM-3(6),SA-8(19),SA-9(6),SC-8(1),SC-12,SC-28(1),SC-28(3)} | |
The [spacecraft] encryption keys shall be restricted so that the onboard software is not able to access the information for key readout.{SV-AC-1,SV-AC-3}{AC-17(6),CM-3(6),SA-8(19),SA-9(6),SC-8(1),SC-12,SC-28(3)} | |
The [spacecraft] encryption keys shall be restricted so that they cannot be read via any telecommands.{SV-AC-1,SV-AC-3}{AC-17(6),CM-3(6),SA-8(19),SA-9(6),SC-8(1),SC-12,SC-28(3)} | |
The [spacecraft] shall produce, control, and distribute symmetric cryptographic keys using NSA Certified or Approved key management technology and processes per CNSSP 12.{SV-AC-1,SV-AC-3}{AC-17(6),CM-3(6),SA-9(6),SC-12,SC-12(1),SC-12(2),SC-12(3)} | |
The [spacecraft] shall use [directional or beamforming] antennas in normal ops to reduce the likelihood that unintended receivers will be able to intercept signals.{SV-AV-1}{AC-18(5)} | |
The [spacecraft] shall provide the capability to restrict command lock based on geographic location of ground stations.{SV-AC-1}{AC-2(11),IA-10,SI-4(13),SI-4(25)} | This could be performed using command lockout based upon when the spacecraft is over selected regions. This should be configurable so that when conflicts arise, the Program can update. The goal is so the spacecraft won't accept a command when the spacecraft determines it is in a certain region. |
The [spacecraft] shall restrict the use of information inputs to spacecraft and designated ground stations as defined in the applicable ICDs.{SV-AC-1,SV-AC-2}{AC-20,SC-23,SI-10,SI-10(5),SI-10(6)} | |
The [spacecraft] shall uniquely identify and authenticate the ground station and other spacecraft before establishing a remote connection.{SV-AC-1,SV-AC-2}{AC-3,AC-17,AC-17(10),AC-20,IA-3,IA-4,SA-8(18),SI-3(9)} | |
The [spacecraft] shall authenticate the ground station (and all commands) and other spacecraft before establishing remote connections using bidirectional authentication that is cryptographically based.{SV-AC-1,SV-AC-2}{AC-3,AC-17,AC-17(2),AC-17(10),AC-18(1),AC-20,IA-3(1),IA-4,IA-4(9),IA-7,IA-9,SA-8(18),SA-8(19),SA-9(2),SC-7(11),SC-16(1),SC-16(2),SC-16(3),SC-23(3),SI-3(9)} | Authorization can include embedding opcodes in command strings, using trusted authentication protocols, identifying proper link characteristics such as emitter location, expected range of receive power, expected modulation, data rates, communication protocols, beamwidth, etc.; and tracking command counter increments against expected values. |
The [spacecraft] shall implement cryptographic mechanisms to identify and reject wireless transmissions that are deliberate attempts to achieve imitative or manipulative communications deception based on signal parameters.{SV-AV-1,SV-IT-1}{AC-3,AC-20,SA-8(19),SC-8(1),SC-23(3),SC-40(3),SI-4(13),SI-4(24),SI-4(25),SI-10(6)} | |
The [spacecraft] shall employ the principle of least privilege, allowing only authorized accesses processes which are necessary to accomplish assigned tasks in accordance with system functions.{SV-AC-6}{AC-3,AC-6,AC-6(9),CA-9,CM-5,CM-5(5),CM-5(6),SA-8(2),SA-8(5),SA-8(6),SA-8(14),SA-8(23),SA-17(7),SC-2,SC-7(29),SC-32,SC-32(1),SI-3} | |
The [spacecraft] shall implement relay and replay-resistant authentication mechanisms for establishing a remote connection.{SV-AC-1,SV-AC-2}{AC-3,IA-2(8),IA-2(9),SA-8(18),SC-8(1),SC-16(1),SC-16(2),SC-23(3),SC-40(4)} | |
The [spacecraft] shall ensure that processes reusing a shared system resource (e.g., registers, main memory, secondary storage) do not have access to information (including encrypted representations of information) previously stored in that resource during a prior use by a process after formal release of that resource back to the system or reuse.{SV-AC-6}{AC-3,PM-32,SA-8(2),SA-8(5),SA-8(6),SA-8(19),SC-4,SI-3} | |
The [spacecraft] shall maintain the confidentiality and integrity of information during preparation for transmission and during reception.{SV-AC-7}{AC-3,SA-8(19),SC-8,SC-8(1),SC-8(2),SC-16,SC-16(1)} | * Preparation for transmission and during reception includes the aggregation, packing, and transformation options performed prior to transmission and the undoing of those operations that occur upon receipt. |
The [spacecraft] shall not employ a mode of operations where cryptography on the TT&C link can be disabled (i.e., crypto-bypass mode).{SV-AC-1,SV-CF-1,SV-CF-2}{AC-3(10),SA-8(18),SA-8(19),SC-16(2),SC-16(3),SC-40(4)} | |
The [spacecraft] software subsystems shall provide non-identical methods, or functionally independent methods, for commanding a mission critical function when the software is the sole control of that function.{SV-MA-3,SV-AV-7}{AC-3(2)} | |
The [spacecraft] software subsystems shall provide two independent and unique command messages to deactivate a fault tolerant capability for a critical or catastrophic hazard.{SV-MA-3,SV-AV-7}{AC-3(2)} | |
The [spacecraft] shall enforce approved authorizations for controlling the flow of information within the platform and between interconnected systems so that information does not leave the platform boundary unless it is encrypted.{SV-AC-6}{AC-3(3),AC-3(4),AC-4,AC-4(6),AC-4(21),CA-3,CA-3(6),CA-3(7),CA-9,IA-9,SA-8(19),SC-8(1),SC-16(3)} | |
The [spacecraft] shall, when transferring information between different security domains, implements the following security policy filters that require fully enumerated formats that restrict data structure and content: connectors and semaphores implemented in the RTOS.{SV-AC-6}{AC-3(3),AC-3(4),AC-4(14),IA-9,SA-8(19),SC-16} | |
The [spacecraft] shall implement boundary protections to separate bus, communications, and payload components supporting their respective functions.{SV-AC-6}{AC-3(3),AC-3(4),CA-9,SA-8(3),SA-8(14),SA-8(18),SA-8(19),SA-17(7),SC-2,SC-2(2),SC-7(13),SC-7(21),SC-7(29),SC-16(3),SC-32,SI-3,SI-4(13),SI-4(25)} | |
The [spacecraft] shall isolate mission critical functionality from non-mission critical functionality by means of an isolation boundary (e.g.via partitions) that controls access to and protects the integrity of, the hardware, software, and firmware that provides that functionality.{SV-AC-6}{AC-3(3),AC-3(4),CA-9,SA-8(3),SA-8(19),SA-17(7),SC-2,SC-3,SC-3(4),SC-7(13),SC-7(29),SC-32,SC-32(1),SI-3,SI-7(10),SI-7(12)} | |
The [spacecraft] data within partitioned applications shall not be read or modified by other applications/partitions.{SV-AC-6}{AC-3(3),AC-3(4),SA-8(19),SC-2(2),SC-4,SC-6,SC-32} | |
The [spacecraft] shall prevent unauthorized access to system resources by employing an efficient capability based object model that supports both confinement and revocation of these capabilities when the platform security deems it necessary.{SV-AC-6}{AC-3(8),IA-4(9),PM-32,SA-8(2),SA-8(5),SA-8(6),SA-8(18),SA-8(19),SC-2(2),SC-4,SC-16,SC-32,SI-3} | |
The [organization] shall state that information should not be allowed to flow between partitioned applications unless explicitly permitted by the Program's security policy.{SV-AC-6}{AC-4,AC-4(6)} | |
The [spacecraft] shall use protected processing domains to enforce the policy that information does not leave the platform boundary unless it is encrypted as a basis for flow control decisions.{SV-AC-6}{AC-4(2),IA-9,SA-8(19),SC-8(1),SC-16(3)} | |
The [spacecraft] shall incorporate backup sources for navigation and timing.{SV-IT-1}{AU-8(1),SC-45(1),SC-45(2)} | |
The [spacecraft] shall have fault-tolerant authoritative time sourcing for the platform's clock.{SV-IT-1}{AU-8(2),SC-45,SC-45(1),SC-45(2),SI-13} | * Adopt voting schemes (triple modular redundancy) that include inputs from backup sources. Consider providing a second reference frame against which short-term changes or interferences can be compared. * Atomic clocks, crystal oscillators and/or GPS receivers are often used as time sources. GPS should not be used as the only source due to spoofing/jamming concerns. |
The [organization] shall ensure that the allocated security safeguards operate in a coordinated and mutually reinforcing manner.{SV-MA-6}{CA-7(5),PL-7,PL-8(1),SA-8(19)} | |
The [organization] shall document and design a security architecture using a defense-in-depth approach that allocates the [organization]s defined safeguards to the indicated locations and layers: [Examples include: operating system abstractions and hardware mechanisms to the separate processors in the platform, internal components, and the FSW].{SV-MA-6}{CA-9,PL-7,PL-8,PL-8(1),SA-8(3),SA-8(4),SA-8(7),SA-8(9),SA-8(11),SA-8(13),SA-8(19),SA-8(29),SA-8(30)} | |
The [spacecraft] shall prevent the installation of Flight Software without verification that the component has been digitally signed using a certificate that is recognized and approved by the ground.{SV-SP-1,SV-SP-3,SV-SP-6,SV-SP-9}{CM-3,CM-3(8),CM-5,CM-5(3),CM-14,SA-8(8),SA-8(31),SA-10(2),SI-3,SI-7(12),SI-7(15)} | |
The [spacecraft] shall provide automatic notification to ground operators upon discovering discrepancies during integrity verification.{SV-IT-2}{CM-3(5),SA-8(21),SI-3,SI-4(7),SI-4(12),SI-4(24),SI-7(2)} | |
The [organization] shall ensure that software planned for reuse meets the fit, form, and function, and security as a component within the new application.{SV-SP-6,SV-SP-7,SV-SP-11}{CM-7(5)} | |
The [spacecraft] operating system, if COTS or FOSS, shall be selected from a [organization]-defined acceptance list.{SV-SP-7}{CM-7(8),CM-7(5)} | |
The [spacecraft] shall enter a cyber-safe mode when conditions that threaten the platform are detected, enters a cyber-safe mode of operation with restrictions as defined based on the cyber-safe mode.{SV-AV-5,SV-AV-6,SV-AV-7}{CP-10(6),CP-12,CP-13,IR-4,IR-4(1),IR-4(3),PE-10,RA-10,SA-8(16),SA-8(21),SA-8(24),SI-3,SI-4(7),SI-13,SI-17} | |
The [spacecraft] shall provide the capability to enter the platform into a known good, operational cyber-safe mode from a tamper-resistant, configuration-controlled (“gold”) image that is authenticated as coming from an acceptable supplier, and has its integrity verified.{SV-AV-5,SV-AV-6,SV-AV-7}{CP-10(6),CP-12,CP-13,IR-4(3),SA-8(16),SA-8(19),SA-8(21),SA-8(24),SI-13,SI-17} | Cyber-safe mode is an operating mode of a spacecraft during which all nonessential systems are shut down and the spacecraft is placed in a known good state using validated software and configuration settings. Within cyber-safe mode authentication and encryption should still be enabled. The spacecraft should be capable of reconstituting firmware and SW functions to preattack levels to allow for the recovery of functional capabilities. This can be performed by self-healing, or the healing can be aided from the ground. However, the spacecraft needs to have the capability to replan, based on available equipment still available after a cyberattack. The goal is for the vehicle to resume full mission operations. If not possible, a reduced level of mission capability should be achieved. |
The [spacecraft] shall fail to a known secure state for failures during initialization, and aborts preserving information necessary to return to operations in failure.{SV-AV-5,SV-AV-6,SV-AV-7}{CP-10(6),CP-13,SA-8(16),SA-8(19),SA-8(24),SC-24,SI-13,SI-17} | |
The [spacecraft] shall fail securely to a secondary device in the event of an operational failure of a primary boundary protection device (i.e., crypto solution).{SV-AC-1,SV-AC-2,SV-CF-1,SV-CF-2}{CP-13,SA-8(19),SA-8(24),SC-7(18),SI-13,SI-13(4)} | |
The [organization] shall define the security safeguards that are to be automatically employed when integrity violations are discovered.{SV-IT-2}{CP-2,SA-8(21),SI-3,SI-4(7),SI-4(12),SI-7(5),SI-7(8)} | |
The [organization] shall define the resources to be allocated to protect the availability of system resources.{SV-AC-6}{CP-2(2),SC-6} | |
The [spacecraft] shall provide or support the capability for recovery and reconstitution to a known state after a disruption, compromise, or failure.{SV-AV-5,SV-AV-6,SV-AV-7}{CP-4(4),CP-10,CP-10(4),CP-10(6),CP-13,IR-4,IR-4(1),SA-8(16),SA-8(19),SA-8(24)} | |
The [spacecraft] shall have multiple uplink paths {SV-AV-1}{CP-8,CP-11,SA-8(18),SC-5,SC-47} | |
The [spacecraft] shall utilize TRANSEC.{SV-AV-1}{CP-8,RA-5(4),SA-8(18),SA-8(19),SC-8(1),SC-8(4),SC-16,SC-16(1),SC-16(2),SC-16(3),SC-40(4)} | Transmission Security (TRANSEC) is used to ensure the availability of transmissions and limit intelligence collection from the transmissions. TRANSEC is secured through burst encoding, frequency hopping, or spread spectrum methods where the required pseudorandom sequence generation is controlled by a cryptographic algorithm and key. Such keys are known as transmission security keys (TSK). The objectives of transmission security are low probability of interception (LPI), low probability of detection (LPD), and antijam which means resistance to jamming (EPM or ECCM). |
The [spacecraft] shall maintain the ability to establish communication with the spacecraft in the event of an anomaly to the primary receive path.{SV-AV-1,SV-IT-1}{CP-8,SA-8(18),SC-47} | Receiver communication can be established after an anomaly with such capabilities as multiple receive apertures, redundant paths within receivers, redundant receivers, omni apertures, fallback default command modes, and lower bit rates for contingency commanding, as examples |
The [spacecraft] shall implement cryptography for the indicated uses using the indicated protocols, algorithms, and mechanisms, in accordance with applicable federal laws, Executive Orders, directives, policies, regulations, and standards: [NSA- certified or approved cryptography for protection of classified information, FIPS-validated cryptography for the provision of hashing].{SV-AC-1,SV-AC-2,SV-CF-1,SV-CF-2,SV-AC-3}{IA-7,SC-13} | |
The [organization] shall implement a security architecture and design that provides the required security functionality, allocates security controls among physical and logical components, and integrates individual security functions, mechanisms, and processes together to provide required security capabilities and a unified approach to protection.{SV-MA-6}{PL-7,SA-2,SA-8,SA-8(1),SA-8(2),SA-8(3),SA-8(4),SA-8(5),SA-8(6),SA-8(7),SA-8(9),SA-8(11),SA-8(13),SA-8(19),SA-8(29),SA-8(30),SC-32,SC-32(1)} | |
The [spacecraft] shall prevent unauthorized and unintended information transfer via shared system resources.{SV-AC-6}{PM-32,SA-8(2),SA-8(5),SA-8(6),SA-8(19),SC-2(2),SC-4} | |
The [spacecraft] shall have on-board intrusion detection/prevention system that monitors the mission critical components or systems.{SV-AC-1,SV-AC-2,SV-MA-4}{RA-10,SC-7,SI-3,SI-3(8),SI-4,SI-4(1),SI-4(7),SI-4(13),SI-4(24),SI-4(25),SI-10(6)} | The mission critical components or systems could be GNC/Attitude Control, C&DH, TT&C, Fault Management. |
The [spacecraft] shall generate error messages that provide information necessary for corrective actions without revealing information that could be exploited by adversaries.{SV-AV-5,SV-AV-6,SV-AV-7}{RA-5(4),SI-4(12),SI-11} | |
The [spacecraft] shall reveal error messages only to operations personnel monitoring the telemetry.{SV-AV-5,SV-AV-6,SV-AV-7}{RA-5(4),SI-4(12),SI-11} | |
The [spacecraft] shall retain the capability to update/upgrade operating systems while on-orbit.{SV-SP-7}{SA-4(5),SA-8(8),SA-8(31),SA-10(2),SI-3} | The operating system updates should be performed using multi-factor authorization and should only be performed when risk of compromise/exploitation of identified vulnerability outweighs the risk of not performing the update. |
The [organization] shall define acceptable secure communication protocols available for use within the mission in accordance with applicable federal laws, Executive Orders, directives, policies, regulations, and standards.{SV-AC-7}{SA-4(9)} | The secure communication protocol should include "strong" authenticated encryption characteristics. |
The [spacecraft] shall only use [organization]-defined communication protocols within the mission.{SV-AC-7}{SA-4(9)} | |
The [spacecraft] shall maintain a separate execution domain for each executing process.{SV-AC-6}{SA-8(14),SA-8(19),SC-2(2),SC-7(21),SC-39,SI-3} | |
The [spacecraft] flight software must not be able to tamper with the security policy or its enforcement mechanisms.{SV-AC-6}{SA-8(16),SA-8(19),SC-3,SC-7(13)} | |
The [spacecraft] shall implement cryptographic mechanisms that achieve adequate protection against the effects of intentional electromagnetic interference.{SV-AV-1,SV-IT-1}{SA-8(19),SC-8(1),SC-40,SC-40(1)} | |
The [organization] shall define and document the transitional state or security-relevant events when the spacecraft will perform integrity checks on software, firmware, and information.{SV-IT-2}{SA-8(21),SI-7(1),SI-7(10),SR-4(4)} | |
The [spacecraft] shall be capable of removing flight software after updated versions have been installed.{SV-SP-1,SV-SP-9}{SA-8(8),SI-2(6)} | |
The [spacecraft] shall provide the capability for data connection ports or input/output devices to be disabled or removed prior to spacecraft operations.{SV-AC-5}{SA-9(2),SC-7(14),SC-41,SC-51} | Intent is for external physical data ports to be disabled (logical or physical) while in operational orbit. Port disablement does not necessarily need to be irreversible. |
The [organization] shall use NIST Approved for symmetric key management for Unclassified systems; NSA Approved or stronger symmetric key management technology for Classified systems.{SV-AC-1,SV-AC-3}{SC-12,SC-12(1),SC-12(2)} | FIPS-complaint technology used by the Program shall include (but is not limited to) cryptographic key generation algorithms or key distribution techniques that are either a) specified in a FIPS, or b) adopted in a FIPS and specified either in an appendix to the FIPS or in a document referenced by the FIPS. NSA-approved technology used for symmetric key management by the Program shall include (but is not limited to) NSA-approved cryptographic algorithms, cryptographic key generation algorithms or key distribution techniques, authentication techniques, or evaluation criteria. |
The [organization] shall use NSA approved key management technology and processes.NSA-approved technology used for asymmetric key management by The [organization] shall include (but is not limited to) NSA-approved cryptographic algorithms, cryptographic key generation algorithms or key distribution techniques, authentication techniques, or evaluation criteria.{SV-AC-1,SV-AC-3}{SC-12,SC-12(1),SC-12(3)} | |
The [spacecraft] shall produce, control, and distribute asymmetric cryptographic keys using [organization]-defined asymmetric key management processes.{SV-AC-1,SV-AC-3}{SC-12,SC-12(1),SC-12(3)} | In most cased the Program will leverage NSA-approved key management technology and processes. |
The [spacecraft] shall discriminate between valid and invalid input into the software and rejects invalid input.{SC-16(2),SI-3(8),SI-10,SI-10(3),SI-10(6)} | |
The [spacecraft] shall identify and reject commands received out-of-sequence when the out-of-sequence commands can cause a hazard/failure or degrade the control of a hazard or mission.{SC-16(2),SI-4(13),SI-4(25),SI-10,SI-10(6),SI-13} | |
The [spacecraft] shall protect the confidentiality and integrity of the [all information] using cryptography while it is at rest.{SV-IT-2,SV-CF-2}{SC-28,SC-28(1),SI-7(6)} | * Information at rest refers to the state of information when it is located on storage devices as specific components of information systems. This is often referred to as data-at-rest encryption. |
The [spacecraft] software subsystems shall provide independent mission/cyber critical threads such that any one credible event will not corrupt another mission/cyber critical thread.{SV-MA-3,SV-AV-7}{SC-3} | |
The [spacecraft] shall internally monitor GPS performance so that changes or interruptions in the navigation or timing are flagged.{SV-IT-1}{SC-45(1)} | |
The [spacecraft] shall protect external and internal communications from jamming and spoofing attempts.{SV-AV-1,SV-IT-1}{SC-5,SC-40,SC-40(1)} | Can be aided via the Crosslink, S-Band, and L-Band subsystems |
The [spacecraft] shall protect the availability of resources by allocating [organization]-defined resources based on [priority and/or quota].{SV-AC-6}{SC-6} | In particular, this control is required for all space platform buses to ensure execution of high priority functions; it is particularly important when there are multiple payloads sharing a bus providing communications and other services, where bus resources must be prioritized based on mission. |
The [organization] shall define the security safeguards to be employed to protect the availability of system resources.{SV-AC-6}{SC-6,SI-17} | |
The [spacecraft] shall monitor [Program defined telemetry points] for malicious commanding attempts.{SV-AC-1,SV-AC-2}{SC-7,AU-3(1),AC-17(1)} | Source from AEROSPACE REPORT NO. TOR-2019-02178 Vehicle Command Counter (VCC) - Counts received valid commands Rejected Command Counter - Counts received invalid commands Command Receiver On/Off Mode - Indicates times command receiver is accepting commands Command Receivers Received Signal Strength - Analog measure of the amount of received RF energy at the receive frequency Command Receiver Lock Modes - Indicates when command receiver has achieved lock on command signal Telemetry Downlink Modes - Indicates when the satellite’s telemetry was transmitting Cryptographic Modes - Indicates the operating modes of the various encrypted links Received Commands - Log of all commands received and executed by the satellite System Clock - Master onboard clock GPS Ephemeris - Indicates satellite location derived from GPS Signals |
The [spacecraft] shall protect the confidentiality and integrity of all transmitted information.{SV-IT-2,SV-AC-7}{SC-8} | * The intent as written is for all transmitted traffic to be protected. This includes internal to internal communications and especially outside of the boundary. |
The [spacecraft] shall implement cryptographic mechanisms to prevent unauthorized disclosure of, and detect changes to, information during transmission unless otherwise protected by alternative physical safeguards.{SV-AC-7}{SC-8(1),SI-7(6)} | |
The [spacecraft] shall maintain the confidentiality and integrity of information during preparation for transmission and during reception.{SV-IT-2}{SC-8(2)} | * Preparation for transmission and during reception includes the aggregation, packing, and transformation options performed prior to transmission and the undoing of those operations that occur upon receipt. |
The [spacecraft] shall implement cryptographic mechanisms to protect message externals unless otherwise protected by alternative physical safeguards.{SV-AC-7}{SC-8(3)} | |
The [spacecraft] software subsystems shall accept [Program defined hazardous] commands only when prerequisite checks are satisfied.{SV-MA-3,SV-AV-7}{SI-10} | |
The [spacecraft] software subsystems shall identify and reject commands received out-of-sequence when the out-of-sequence commands can cause a hazard/failure or degrade the control of a hazard or mission.{SV-MA-3,SV-AV-7}{SI-10} | |
The [spacecraft] software subsystems shall perform prerequisite checks for the execution of hazardous commands.{SV-MA-3,SV-AV-7}{SI-10} | |
The [organization] shall ensure that all viable commands are known to the mission and SV "owner.{SV-AC-8}{SI-10,SI-10(3)} | This is a concern for bus re-use. It is possible that the manufacturer left previously coded commands in their syntax rather than starting from a clean slate. This leaves potential backdoors and other functionality the mission does not know about. |
The [organization] shall perform analysis of critical (backdoor) commands that could adversely affect mission success if used maliciously.{SV-AC-8}{SI-10,SI-10(3)} | Heritage and commercial products often have many residual operational (e.g., hardware commands) and test capabilities that are unidentified or unknown to the end user, perhaps because they were not expressly stated mission requirements. These would never be tested and their effects unknown, and hence, could be used maliciously. Test commands not needed for flight should be deleted from the flight database. |
The [spacecraft] shall only use or include [organization]-defined critical commands for the purpose of providing emergency access where commanding authority is appropriately restricted.{SV-AC-8}{SI-10,SI-10(3)} | The intent is protect against misuse of critical commands. On potential scenario is where you could use accounts with different privileges, could require an additional passphrase or require entry into a different state or append an additional footer to a critical command. There is room for design flexibility here that can still satisfy this requirement. |
The [spacecraft] software subsystems shall discriminate between valid and invalid input into the software and rejects invalid input.{SV-MA-3,SV-AV-7}{SI-10,SI-10(3)} | |
The [spacecraft] software subsystems shall properly handle spurious input and missing data.{SV-MA-3,SV-AV-7}{SI-10,SI-10(3)} | |
The [spacecraft] shall properly handle spurious input and missing data.{SI-10,SI-10(3),SI-10(6)} | |
The [spacecraft] shall perform prerequisite checks for the execution of hazardous commands.{SI-10,SI-10(6),SI-13} | |
The [spacecraft] software subsystems shall validate a functionally independent parameter prior to the issuance of any sequence that could remove an inhibit or perform a hazardous action.{SV-MA-3,SV-AV-7}{SI-10(3)} | |
The [spacecraft] mission/cyber critical commands shall be "complex" and/or diverse from other commands so that a single bit flip could not transform a benign command into a hazardous command.{SV-MA-3,SV-AV-7}{SI-10(5)} | |
The [spacecraft] software subsystems shall provide at least one independent command for each operator-initiated action used to shut down a function leading to or reducing the control of a hazard.{SV-MA-3,SV-AV-7}{SI-10(5)} | |
The [spacecraft] shall have failure tolerance on sensors used by software to make mission-critical decisions.{SV-MA-3,SV-AV-7}{SI-13,SI-17} | |
The [spacecraft] cyber-safe mode software/configuration should be stored onboard the spacecraft in memory with hardware-based controls and should not be modifiable.{SV-AV-5,SV-AV-6,SV-AV-7}{SI-17} | Cyber-safe mode is using a fail-secure mentality where if there is a malfunction that the spacecraft goes into a fail-secure state where cyber protections like authentication and encryption are still employed (instead of bypassed) and the spacecraft can be restored by authorized commands. The cyber-safe mode should be stored in a high integrity location of the on-board SV so that it cannot be modified by attackers. |
The [spacecraft] software subsystems shall detect and recover/transition from detected memory errors to a known cyber-safe state.{SV-MA-3,SV-AV-7}{SI-17} | |
The [spacecraft] software subsystems shall initialize the spacecraft to a known safe state.{SV-MA-3,SV-AV-7}{SI-17} | |
The [spacecraft] software subsystems shall operate securely in off-nominal power conditions, including loss of power and spurious power transients.{SV-MA-3,SV-AV-7}{SI-17} | |
The [spacecraft] software subsystems shall perform an orderly, controlled system shutdown to a known cyber-safe state upon receipt of a termination command or condition.{SV-MA-3,SV-AV-7}{SI-17} | |
The [spacecraft] software subsystems shall recover to a known cyber-safe state when an anomaly is detected.{SV-MA-3,SV-AV-7}{SI-17} | |
The [spacecraft] software subsystems shall safely transition between all predefined, known states.{SV-MA-3,SV-AV-7}{SI-17} | |
The [spacecraft] shall only use or include critical commands for the purpose of providing emergency access where commanding authority is appropriately restricted.{SI-3(8),SI-10,SI-10(3)} | |
The [spacecraft] shall perform an integrity check of [Program-defined software, firmware, and information] at startup; at [Program-defined transitional states or security-relevant events] {SV-IT-2}{SI-7(1)} | |
The [organization] shall employ automated tools that provide notification to [Program-defined personnel] upon discovering discrepancies during integrity verification.{SV-IT-2}{SI-7(2)} | |
The [spacecraft] shall automatically [Selection (one or more):restarts the FSW/processor, performs side swap, audits failure; implements Program-defined security safeguards] when integrity violations are discovered.{SV-IT-2}{SI-7(8)} | |
The [spacecraft] shall utilize strong fault management and redundancy to help mitigate threats against TT&C failure.{SV-AV-7} |
ID | Name | Description | |
---|---|---|---|
REC-0001 | Gather Spacecraft Design Information | Threat actors may gather information about the victim SV's design that can be used for future campaigns or to help perpetuate other techniques. Information about the SV can include software, firmware, encryption type, purpose, as well as various makes and models of subsystems. | |
REC-0001.01 | Software | Threat actors may gather information about the victim SV's internal software that can be used for future campaigns or to help perpetuate other techniques. Information (e.g. source code, binaries, etc.) about commercial, open-source, or custom developed software may include a variety of details such as types, versions, and memory maps. Leveraging this information threat actors may target vendors of operating systems, flight software, or open-source communities to embed backdoors or for performing reverse engineering research to support offensive cyber operations. | |
REC-0001.02 | Firmware | Threat actors may gather information about the victim SV's firmware that can be used for future campaigns or to help perpetuate other techniques. Information about the firmware may include a variety of details such as type and versions on specific devices, which may be used to infer more information (ex. configuration, purpose, age/patch level, etc.). Leveraging this information threat actors may target firmware vendors to embed backdoors or for performing reverse engineering research to support offensive cyber operations. | |
REC-0001.03 | Cryptographic Algorithms | Threat actors may gather information about any cryptographic algorithms used on the victim SV's that can be used for future campaigns or to help perpetuate other techniques. Information about the algorithms can include type and private keys. Threat actors may also obtain the authentication scheme (i.e., key/password/counter values) and leverage it to establish communications for commanding the target SV or any of its subsystems. Some SVs only require authentication vice authentication and encryption, therefore once obtained, threat actors may use any number of means to command the spacecraft without needing to go through a legitimate channel. The authentication information may be obtained through reconnaissance of the ground system or retrieved from the victim SV. | |
REC-0001.04 | Data Bus | Threat actors may gather information about the data bus used within the victim SV that can be used for future campaigns or to help perpetuate other techniques. Information about the data bus can include the make and model which could lead to more information (ex. protocol, purpose, controller, etc.), as well as locations/addresses of major subsystems residing on the bus. Threat actors may also gather information about the bus voltages of the victim SV. This information can include optimal power levels, connectors, range, and transfer rate. | |
REC-0001.05 | Thermal Control System | Threat actors may gather information about the thermal control system used with the victim SV that can be used for future campaigns or to help perpetuate other techniques. Information gathered can include type, make/model, and varies analysis programs that monitor it. | |
REC-0001.06 | Maneuver & Control | Threat actors may gather information about the station-keeping control systems within the victim SV that can be used for future campaigns or to help perpetuate other techniques. Information gathered can include thruster types, propulsion types, attitude sensors, and data flows associated with the relevant subsystems. | |
REC-0001.07 | Payload | Threat actors may gather information about the type(s) of payloads hosted on the victim SV. This information could include specific commands, make and model, and relevant software. Threat actors may also gather information about the location of the payload on the bus and internal routing as it pertains to commands within the payload itself. | |
REC-0001.08 | Power | Threat actors may gather information about the power system used within the victim SV. This information can include type, power intake, and internal algorithms. Threat actors may also gather information about the solar panel configurations such as positioning, automated tasks, and layout. Additionally, threat actors may gather information about the batteries used within the victim SV. This information can include the type, quantity, storage capacity, make and model, and location. | |
REC-0001.09 | Fault Management | Threat actors may gather information about any fault management that may be present on the victim SV. This information can help threat actors construct specific attacks that may put the SV into a fault condition and potentially a more vulnerable state depending on the fault response. | |
REC-0002 | Gather Spacecraft Descriptors | Threat actors may gather information about the victim SV's descriptors that can be used for future campaigns or to help perpetuate other techniques. Information about the descriptors may include a variety of details such as identity attributes, organizational structures, and mission operational parameters. | |
REC-0002.01 | Identifiers | Threat actors may gather information about the victim SV's identity attributes that can be used for future campaigns or to help perpetuate other techniques. Information may include a variety of details such as the satellite catalog number, international designator, mission name, and more. | |
REC-0002.02 | Organization | Threat actors may gather information about the victim SV's associated organization(s) that can be used for future campaigns or to help perpetuate other techniques. Collection efforts may target the mission owner/operator in order to conduct further attacks against the organization, individual, or other interested parties. Threat actors may also seek information regarding the SV's designer/builder, including physical locations, key employees, and roles and responsibilities as they pertain to the SV, as well as information pertaining to the mission's end users/customers. | |
REC-0002.03 | Operations | Threat actors may gather information about the victim SV's operations that can be used for future campaigns or to help perpetuate other techniques. Collection efforts may target mission objectives, orbital parameters such as orbit slot and inclination, user guides and schedules, etc. Additionally, threat actors may seek information about constellation deployments and configurations where applicable. | |
REC-0003 | Gather Spacecraft Communications Information | Threat actors may obtain information on the victim SV's communication channels in order to determine specific commands, protocols, and types. Information gathered can include commanding patterns, antenna shape and location, beacon frequency and polarization, and various transponder information. | |
REC-0003.01 | Communications Equipment | Threat actors may gather information regarding the communications equipment and its configuration that will be used for communicating with the victim SV. This includes: Antenna Shape: This information can help determine the range in which it can communicate, the power of it's transmission, and the receiving patterns. Antenna Configuration/Location: This information can include positioning, transmission frequency, wavelength, and timing. Telemetry Signal Type: Information can include timing, radio frequency wavelengths, and other information that can provide insight into the spacecraft's telemetry system. Beacon Frequency: This information can provide insight into where the SV is located, what it's orbit is, and how long it can take to communicate with a ground station. Beacon Polarization: This information can help triangulate the SV as it orbits the earth and determine how a satellite must be oriented in order to communicate with the victim SV. Transponder: This could include the number of transponders per band, transponder translation factor, transponder mappings, power utilization, and/or saturation point. | |
REC-0003.02 | Commanding Details | Threat actors may gather information regarding the commanding approach that will be used for communicating with the victim SV. This includes: Commanding Signal Type: This can include timing, radio frequency wavelengths, and other information that can provide insight into the spacecraft's commanding system. Valid Commanding Patterns: Most commonly, this comes in the form of a command database, but can also include other means that provide information on valid commands and the communication protocols used by the victim SV. Valid Commanding Periods: This information can provide insight into when a command will be accepted by the SV and help the threat actor construct a viable attack campaign. | |
REC-0004 | Gather Launch Information | Threat actors may gather the launch date and time, location of the launch (country & specific site), organizations involved, launch vehicle, etc. This information can provide insight into protocols, regulations, and provide further targets for the threat actor, including specific vulnerabilities with the launch vehicle itself. | |
REC-0004.01 | Flight Termination | Threat actor may obtain information regarding the vehicle's flight termination system. Threat actors may use this information to perform later attacks and target the vehicle's termination system to have desired impact on mission. | |
REC-0005 | Eavesdropping | Threat actors may seek to capture network communications throughout the ground station and radio frequency (RF) communication used for uplink and downlink communications. RF communication frequencies vary between 30MHz and 60 GHz. Threat actors may capture RF communications using specialized hardware, such as software defined radio (SDR), handheld radio, or a computer with radio demodulator turned to the communication frequency. Network communications may be captured using packet capture software while the threat actor is on the target network. | |
REC-0005.01 | Uplink Intercept | Threat actors may capture the RF communications as it pertains to the uplink to the victim SV. This information can contain commanding information that the threat actor can use to perform other attacks against the victim SV. | |
REC-0005.02 | Downlink Intercept | Threat actors may capture the RF communications as it pertains to the downlink of the victim SV. This information can contain important telemetry such as onboard status and mission data. | |
REC-0005.03 | Proximity Operations | Threat actors may capture signals and/or network communications as they travel on-board the vehicle (i.e., EMSEC/TEMPEST), via RF, or terrestrial networks. This information can be decoded to determine commanding and telemetry protocols, command times, and other information that could be used for future attacks. | |
REC-0006 | Gather FSW Development Information | Threat actors may obtain information regarding the flight software (FSW) development environment for the victim SV. This information may include the development environment, source code, compiled binaries, testing tools, and fault management. | |
REC-0006.01 | Development Environment | Threat actors may gather information regarding the development environment for the victim SV's FSW. This information can include IDEs, configurations, source code, environment variables, source code repositories, code "secrets", and compiled binaries. | |
REC-0006.02 | Security Testing Tools | Threat actors may gather information regarding how a victim SV is tested in regards to the FSW. Understanding the testing approach including tools could identify gaps and vulnerabilities that could be discovered and exploited by a threat actor. | |
REC-0007 | Monitor for Safe-Mode Indicators | Threat actors may gather information regarding safe-mode indicators on the victim SV. Safe-mode is when all non-essential systems are shut down and only essential functions within the SV are active. During this mode, several commands are available to be processed that are not normally processed. Further, many protections may be disabled at this time. | |
REC-0008 | Gather Supply Chain Information | Threat actors may gather information about a mission's supply chain or product delivery mechanisms that can be used for future campaigns or to help perpetuate other techniques. | |
REC-0008.01 | Hardware | Threat actors may gather information that can be used to facilitate a future attack where they manipulate hardware components in the victim SV prior to the customer receiving them in order to achieve data or system compromise. The threat actor can insert backdoors and give them a high level of control over the system when they modify the hardware or firmware in the supply chain. This would include ASIC and FPGA devices as well. | |
REC-0008.02 | Software | Threat actors may gather information relating to the mission's software supply chain in order to facilitate future attacks to achieve data or system compromise. This attack can take place in a number of ways, including manipulation of source code, manipulation of the update and/or distribution mechanism, or replacing compiled versions with a malicious one. | |
REC-0008.03 | Known Vulnerabilities | Threat actors may gather information about vulnerabilities that can be used for future campaigns or to perpetuate other techniques. A vulnerability is a weakness in the victim SV's hardware, subsystems, bus, or software that can, potentially, be exploited by a threat actor to cause unintended or unanticipated behavior to occur. During reconnaissance as threat actors identify the types/versions of software (i.e., COTS, open-source) being used, they will look for well-known vulnerabilities that could affect the space vehicle. Threat actors may find vulnerability information by searching leaked documents, vulnerability databases/scanners, compromising ground systems, and searching through online databases. | |
REC-0009 | Gather Mission Information | Threat actors may initially seek to gain an understanding of a target mission by gathering information commonly captured in a Concept of Operations (or similar) document and related artifacts. Information of interest includes, but is not limited to: - the needs, goals, and objectives of the system - system overview and key elements/instruments - modes of operations (including operational constraints) - proposed capabilities and the underlying science/technology used to provide capabilities (i.e., scientific papers, research studies, etc.) - physical and support environments | |
RD-0002 | Compromise Infrastructure | Threat actors may compromise third-party infrastructure that can be used for future campaigns or to perpetuate other techniques. Infrastructure solutions include physical devices such as antenna, amplifiers, and convertors, as well as software used by satellite communicators. Instead of buying or renting infrastructure, a threat actor may compromise infrastructure and use it during other phases of the campaign's lifecycle. | |
RD-0002.01 | Mission-Operated Ground System | Threat actors may compromise mission owned/operated ground systems that can be used for future campaigns or to perpetuate other techniques. These ground systems have already been configured for communications to the victim SV. By compromising this infrastructure, threat actors can stage, launch, and execute an operation. Threat actors may utilize these systems for various tasks, including Execution and Exfiltration. | |
RD-0002.02 | 3rd Party Ground System | Threat actors may compromise access to third-party ground systems that can be used for future campaigns or to perpetuate other techniques. These ground systems can be or may have already been configured for communications to the victim SV. By compromising this infrastructure, threat actors can stage, launch, and execute an operation. | |
RD-0003 | Obtain Capabilities | Threat actors may buy and/or steal capabilities that can be used for future campaigns or to perpetuate other techniques. Rather than developing their own capabilities in-house, threat actors may purchase, download, or steal them. Activities may include the acquisition of malware, software, exploits, and information relating to vulnerabilities. Threat actors may obtain capabilities to support their operations throughout numerous phases of the campaign lifecycle. | |
RD-0003.02 | Cryptographic Keys | Threat actors may obtain encryption keys as they are used for the main commanding of the target SV or any of its subsystems/payloads. Once obtained, threat actors may use any number of means to command the spacecraft without needing to go through a legitimate channel. These keys may be obtained through reconnaissance of the ground system or retrieved from the victim SV. | |
RD-0004 | Stage Capabilities | Threat actors may upload, install, or otherwise set up capabilities that can be used for future campaigns or to perpetuate other techniques. To support their operations, a threat actor may need to develop their own capabilities or obtain them in some way in order to stage them on infrastructure under their control. These capabilities may be staged on infrastructure that was previously purchased or rented by the threat actor or was otherwise compromised by them. | |
RD-0004.01 | Identify/Select Delivery Mechanism | Threat actors may identify, select, and prepare a delivery mechanism in which to attack the space system (i.e., communicate with the victim SV, deny the ground, etc.) to achieve their desired impact. This mechanism may be located on infrastructure that was previously purchased or rented by the threat actor or was otherwise compromised by them. The mechanism must include all aspects needed to communicate with the victim SV, including ground antenna, converters, and amplifiers. | |
RD-0004.02 | Upload Exploit/Payload | Threat actors may upload exploits and payloads to a third-party infrastructure that they have purchased or rented or stage it on an otherwise compromised ground station. Exploits and payloads would include files and commands to be uploaded to the victim SV in order to conduct the threat actor's attack. | |
IA-0002 | Compromise Software Defined Radio | Threat actors may target software defined radios due to their software nature to establish C2 channels. Since SDRs are programmable, when combined with supply chain or development environment attacks, SDRs provide a pathway to setup covert C2 channels for a threat actor. | |
IA-0003 | Crosslink via Compromised Neighbor | Threat actors may compromise a victim SV via the crosslink communications of a neighboring SV that has been compromised. SVs in close proximity are able to send commands back and forth. Threat actors may be able to leverage this access to compromise other SVs once they have access to another that is nearby. | |
IA-0004 | Secondary/Backup Communication Channel | Threat actors may compromise alternative communication pathways which may not be as protected as the primary pathway. Depending on implementation the contingency communication pathways/solutions may lack the same level of security (i.e., physical security, encryption, authentication, etc.) which if forced to use could provide a threat actor an opportunity to launch attacks. Typically these would have to be coupled with other denial of service techniques on the primary pathway to force usage of secondary pathways. | |
IA-0004.01 | Ground Station | Threat actors may establish a foothold within the backup ground/mission operations center (MOC) and then perform attacks to force primary communication traffic through the backup communication channel so that other TTPs can be executed (man-in-the-middle, malicious commanding, malicious code, etc.). While an attacker would not be required to force the communications through the backup channel vice waiting until the backup is used for various reasons. The backup ground/MOC should be considered a viable attack vector and the appropriate/equivalent security controls from the primary communication channel should be on the backup ground/MOC as well. | |
IA-0005 | Rendezvous & Proximity Operations | Threat actors may perform a space rendezvous which is a set of orbital maneuvers during which a spacecraft arrives at the same orbit and approach to a very close distance (e.g. within visual contact or close proximity) to a target SV. | |
IA-0005.01 | Compromise Emanations | Threat actors in close proximity may intercept and analyze electromagnetic radiation emanating from cryptoequipment and/or the target SV (i.e., main bus) to determine whether the emanations are information bearing. The data could be used to establish initial access. | |
IA-0005.02 | Docked Vehicle / OSAM | Threat actors may leverage docking vehicles to laterally move into a target SV. If information is known on docking plans, a threat actor may target vehicles on the ground or in space to deploy malware to laterally move or execute malware on the target SV via the docking interface. | |
IA-0005.03 | Proximity Grappling | Threat actors may posses the capability to grapple target SVs once it has established the appropriate space rendezvous. If from a proximity / rendezvous perspective a threat actor has the ability to connect via docking interface or expose testing (i.e., JTAG port) once it has grappled the target SV, they could perform various attacks depending on the access enabled via the physical connection. | |
IA-0006 | Compromise Hosted Payload | Threat actors may compromise the target SV hosted payload to initially access and/or persist within the system. Hosted payloads can usually be accessed from the ground via a specific command set. The command pathways can leverage the same ground infrastructure or some host payloads have their own ground infrastructure which can provide an access vector as well. Threat actors may be able to leverage the ability to command hosted payloads to upload files or modify memory addresses in order to compromise the system. Depending on the implementation, hosted payloads may provide some sort of lateral movement potential. | |
IA-0007 | Compromise Ground Station | Threat actors may initially compromise the ground station in order to access the target SV. Once compromised, the threat actor can perform a multitude of initial access techniques, including replay, compromising FSW deployment, compromising encryption keys, and compromising authentication schemes. | |
IA-0007.01 | Compromise On-Orbit Update | Threat actors may manipulate and modify on-orbit updates before they are sent to the target SV. This attack can be done in a number of ways, including manipulation of source code, manipulating environment variables, on-board table/memory values, or replacing compiled versions with a malicious one. | |
IA-0007.02 | Malicious Commanding via Valid GS | Threat actors may compromise target owned ground systems components (e.g., front end processors, command and control software, etc.) that can be used for future campaigns or to perpetuate other techniques. These ground systems components have already been configured for communications to the victim SV. By compromising this infrastructure, threat actors can stage, launch, and execute an operation. Threat actors may utilize these systems for various tasks, including Execution and Exfiltration. | |
IA-0008 | Rogue External Entity | Threat actors may gain access to a victim SV through the use of a rogue external entity. With this technique, the threat actor does not need access to a legitimate ground station or communication site. | |
IA-0008.01 | Rogue Ground Station | Threat actors may gain access to a victim SV through the use of a rogue ground system. With this technique, the threat actor does not need access to a legitimate ground station or communication site. | |
IA-0008.02 | Rogue Spacecraft | Threat actors may gain access to a target SV using their own SV that has the capability to maneuver within close proximity to a target SV to carry out a variety of TTPs (i.e., eavesdropping, side-channel, etc.). Since many of the commercial and military assets in space are tracked, and that information is publicly available, attackers can identify the location of space assets to infer the best positioning for intersecting orbits. Proximity operations support avoidance of the larger attenuation that would otherwise affect the signal when propagating long distances, or environmental circumstances that may present interference. | |
IA-0009 | Trusted Relationship | Access through trusted third-party relationship exploits an existing connection that has been approved for interconnection. Leveraging third party / approved interconnections to pivot into the target systems is a common technique for threat actors as these interconnections typically lack stringent access control due to the trusted status. | |
IA-0009.01 | Mission Collaborator (academia, international, etc.) | Threat actors may seek to exploit mission partners to gain an initial foothold for pivoting into the mission environment and eventually impacting the SV. The complex nature of many space systems rely on contributions across organizations, including academic partners and even international collaborators. These organizations will undoubtedly vary in their system security posture and attack surface. | |
IA-0009.02 | Vendor | Threat actors may target the trust between vendors and the target space vehicle. Missions often grant elevated access to vendors in order to allow them to manage internal systems as well as cloud-based environments. The vendor's access may be intended to be limited to the infrastructure being maintained but it may provide laterally movement into the target space vehicle. Attackers may leverage security weaknesses in the vendor environment to gain access to more critical mission resources or network locations. In the space vehicle context vendors may have direct commanding and updating capabilities outside of the primary communication channel. | |
IA-0009.03 | User Segment | Threat actors can target the user segment in an effort to laterally move into other areas of the end-to-end mission architecture. When user segments are interconnected, threat actors can exploit lack of segmentation as the user segment's security undoubtedly varies in their system security posture and attack surface than the primary space mission. The user equipment and users themselves provide ample attack surface as the human element and their vulnerabilities (i.e., social engineering, phishing, iOT) are often the weakest security link and entry point into many systems. | |
IA-0010 | Exploit Reduced Protections During Safe-Mode | Threat actors may take advantage of the victim SV being in safe mode and send malicious commands that may not otherwise be processed. Safe-mode is when all non-essential systems are shut down and only essential functions within the SV are active. During this mode, several commands are available to be processed that are not normally processed. Further, many protections may be disabled at this time. | |
IA-0012 | Assembly, Test, and Launch Operation Compromise | Threat actors may target the spacecraft hardware and/or software while the spacecraft is at Assembly, Test, and Launch Operation (ATLO). ATLO is often the first time pieces of the spacecraft are fully integrated and exchanging data across interfaces. Malware could propagate from infected devices across the integrated spacecraft. For example, test equipment (i.e., transient cyber asset) is often brought in for testing elements of the spacecraft. Additionally, varying levels of physical security is in place which may be a reduction in physical security typically seen during development. The ATLO environment should be considered a viable attack vector and the appropriate/equivalent security controls from the primary development environment should be implemented during ATLO as well. | |
EX-0001 | Replay | Replay attacks involve threat actors recording previously data streams and then resending them at a later time. This attack can be used to fingerprint systems, gain elevated privileges, or even cause a denial of service. | |
EX-0001.01 | Command Packets | Threat actors may interact with the victim SV by replaying captured commands to the SV. While not necessarily malicious in nature, replayed commands can be used to overload the target SV and cause it's onboard systems to crash, perform a DoS attack, or monitor various responses by the SV. If critical commands are captured and replayed, thruster fires, then the impact could impact the SV's attitude control/orbit. | |
EX-0001.02 | Bus Traffic | Threat actors may abuse internal commanding to replay bus traffic within the victim SV. On-board resources within the SV are very limited due to the number of subsystems, payloads, and sensors running at a single time. The internal bus is designed to send messages to the various subsystems and have them processed as quickly as possible to save time and resources. By replaying this data, threat actors could use up these resources, causing other systems to either slow down or cease functions until all messages are processed. Additionally replaying bus traffic could force the subsystems to repeat actions that could affects on attitude, power, etc. | |
EX-0003 | Modify Authentication Process | Threat actors may modify the internal authentication process of the victim SV to facilitate initial access, recurring execution, or prevent authorized entities from accessing the SV. This can be done through the modification of the software binaries or memory manipulation techniques. | |
EX-0005 | Exploit Hardware/Firmware Corruption | Threat actors can target the underlying hardware and/or firmware using various TTPs that will be dependent on the specific hardware/firmware. Typically, software tools (e.g., antivirus, antimalware, intrusion detection) can protect a system from threat actors attempting to take advantage of those vulnerabilities to inject malicious code. However, there exist security gaps that cannot be closed by the above-mentioned software tools since they are not stationed on software applications, drivers or the operating system but rather on the hardware itself. Hardware components, like memory modules and caches, can be exploited under specific circumstances thus enabling backdoor access to potential threat actors. In addition to hardware, the firmware itself which often is thought to be software in its own right also provides an attack surface for threat actors. Firmware is programming that's written to a hardware device's non-volatile memory where the content is saved when a hardware device is turned off or loses its external power source. Firmware is written directly onto a piece of hardware during manufacturing and it is used to run on the device and can be thought of as the software that enables hardware to run. In the space vehicle context, firmware and field programmable gate array (FPGA)/application-specific integrated circuit (ASIC) logic/code is considered equivalent to firmware. | |
EX-0005.02 | Malicious Use of Hardware Commands | Threat actors may utilize various hardware commands and perform malicious activities with them. Hardware commands typically differ from traditional command channels as they bypass many of the traditional protections and pathways and are more direct therefore they can be dangerous if not protected. Hardware commands are sometime a necessity to perform various actions such as configuring sensors, adjusting positions, and rotating internal motors. Threat actors may use these commands to perform malicious activities that can damage the victim SV in some capacity. | |
EX-0006 | Disable/Bypass Encryption | Threat actors may perform specific techniques in order to bypass or disable the encryption mechanism onboard the victim SV. By bypassing or disabling this particular mechanism, further tactics can be performed, such as Exfiltration, that may have not been possible with the internal encryption process in place. | |
EX-0011 | Exploit Reduced Protections During Safe-Mode | Threat actors may take advantage of the victim SV being in safe mode and send malicious commands that may not otherwise be processed. Safe-mode is when all non-essential systems are shut down and only essential functions within the SV are active. During this mode, several commands are available to be processed that are not normally processed. Further, many protections may be disabled at this time. | |
EXF-0002 | Side-Channel Attack | Threat actors may use a side-channel attack attempts to gather information by measuring or exploiting indirect effects of the SV. Information within the SV can be extracted through these side-channels in which sensor data is analyzed in non-trivial ways to recover subtle, hidden or unexpected information. A series of measurements of a side-channel constitute an identifiable signature which can then be matched against a signature database to identify target information, without having to explicitly decode the side-channel. | |
EXF-0002.04 | Timing Attacks | Threat actors can leverage timing attacks to exfiltrate information due to variances in the execution timing for different sub-systems in the spacecraft (i.e., cryptosystem). In spacecraft, due to the utilization of processors with lower processing powers (i.e. slow), this becomes all the more important because slower processors will enhance even small difference in computation time. Every operation in a spacecraft takes time to execute, and the time can differ based on the input; with precise measurements of the time for each operation, a threat actor can work backwards to the input. Finding secrets through timing information may be significantly easier than using cryptanalysis of known plaintext, ciphertext pairs. Sometimes timing information is combined with cryptanalysis to increase the rate of information leakage. | |
EXF-0001 | Replay | Threat actors may exfiltrate data by replaying commands and capturing the telemetry or payload data as it is sent down. One scenario would be the threat actor replays commands to downlink payload data once SV is within certain location so the data can be intercepted on the downlink by threat actor ground terminals. | |
EXF-0003 | Eavesdropping | Threat actors may seek to capture network communications throughout the ground station and communication channel (i.e. radio frequency, optical) used for uplink and downlink communications | |
EXF-0003.01 | Uplink Intercept | Threat actors may target the uplink connection from the victim ground infrastructure to the target SV in order to exfiltrate commanding data. Depending on the implementation (i.e., encryption) the captured uplink data can be used to further other attacks like command link intrusion, replay, etc. | |
EXF-0003.02 | Downlink Intercept | Threat actors may target the downlink connection from the victim SV in order to exfiltrate telemetry or payload data. This data can include health information of the SV or whatever mission data that is being collected/analyzed on the SV. | |
EXF-0004 | Out-of-Band Communications Link | Threat actors may attempt to exfiltrate data via the out-of-band communication channels. While performing eavesdropping on the primary/second uplinks and downlinks is a method for exfiltration, some space vehicles leverage out-of-band communication links to perform actions on the space vehicle (i.e., re-keying). These out-of-band links would occur on completely different channels/frequencies and often operate on separate hardware on the space vehicle. Typically these out-of-band links have limited built-for-purpose functionality and likely do not present an initial access vector but they do provide ample exfiltration opportunity. | |
EXF-0005 | Proximity Operations | Threat actors may leverage the lack of emission security or tempest controls to exfiltrate information using a visiting SV. This is similar to side-channel attacks but leveraging a visiting SV to measure the signals for decoding purposes. | |
EXF-0006 | Modify Software Defined Radio | Threat actors may target software defined radios due to their software nature to setup exfiltration channels. Since SDRs are programmable, when combined with supply chain or development environment attacks, SDRs provide a pathway to setup covert exfiltration channels for a threat actor. | |
EXF-0007 | Compromised Ground Station | Threat actors may compromise target owned ground systems that can be used for future campaigns or to perpetuate other techniques. These ground systems have already been configured for communications to the victim SV. By compromising this infrastructure, threat actors can stage, launch, and execute an operation. Threat actors may utilize these systems for various tasks, including Execution and Exfiltration. | |
EXF-0008 | Compromised Developer Site | Threat actors may compromise development environments located within the ground system or a developer/partner site. This attack can take place in a number of different ways, including manipulation of source code, manipulating environment variables, or replacing compiled versions with a malicious one. This technique is usually performed before the target SV is in orbit, with the hopes of adding malicious code to the actual FSW during the development process. | |
EXF-0009 | Compromised Partner Site | Threat actors may compromise access to partner sites that can be used for future campaigns or to perpetuate other techniques. These sites are typically configured for communications to the primary ground station(s) or in some cases the SV itself. Unlike mission operated ground systems, partner sites may provide an easier target for threat actors depending on the company, roles and responsibilities, and interests of the third-party. By compromising this infrastructure, threat actors can stage, launch, and execute an operation. Threat actors may utilize these systems for various tasks, including Execution and Exfiltration. | |
PER-0002 | Backdoor | Threat actors may find and target various backdoors, or inject their own, within the victim SV in the hopes of maintaining their attack. | |
PER-0002.01 | Hardware | Threat actors may find and target various hardware backdoors within the victim SV in the hopes of maintaining their attack. Once in orbit, mitigating the risk of various hardware backdoors becomes increasingly difficult for ground controllers. By targeting these specific vulnerabilities, threat actors are more likely to remain persistent on the victim SV and perpetuate further attacks. | |
PER-0002.02 | Software | Threat actors may inject code to create their own backdoor to establish persistent access to the SV. This may be done through modification of code throughout the software supply chain or through modification of the software-defined radio configuration (if applicable). | |
PER-0003 | Ground System Presence | Threat actors may compromise target owned ground systems that can be used for persistent access to the SV or to perpetuate other techniques. These ground systems have already been configured for communications to the victim SV. By compromising this infrastructure, threat actors can stage, launch, and execute persistently. | |
PER-0004 | Replace Cryptographic Keys | Threat actors may attempt to fully replace the cryptographic keys on the space vehicle which could lockout the mission operators and enable the threat actor's communication channel. Once the encryption key is changed on the space vehicle, the SV is rendered inoperable from the operators perspective as they have lost commanding access. Threat actors may exploit weaknesses in the key management strategy. For example, the threat actor may exploit the over-the-air rekeying procedures to inject their own cryptographic keys. | |
DE-0002 | Prevent Downlink | Threat actors may target the downlink connections to prevent the victim SV from sending telemetry to the ground controllers. Telemetry is the only method in which ground controllers can monitor the health and stability of the SV while in orbit. By disabling this downlink, threat actors may be able to stop mitigations from taking place. | |
DE-0002.01 | Inhibit Ground System Functionality | Threat actors may utilize ground-system presence to inhibit the ground system software's ability to process (or display) telemetry, effectively leaving ground controllers unaware of vehicle activity during this time. Telemetry is the only method in which ground controllers can monitor the health and stability of the SV while in orbit. By disabling this downlink, threat actors may be able to stop mitigations from taking place. | |
DE-0002.02 | Jam Link Signal | Threat actors may overwhelm/jam the downlink signal to prevent transmitted telemetry signals from reaching their destination without severe modification/interference, effectively leaving ground controllers unaware of vehicle activity during this time. Telemetry is the only method in which ground controllers can monitor the health and stability of the SV while in orbit. By disabling this downlink, threat actors may be able to stop mitigations from taking place. | |
DE-0004 | Masquerading | Threat actors may gain access to a victim SV by masquerading as an authorized entity. This can be done several ways, including through the manipulation of command headers, spoofing locations, or even leveraging Insider's access (i.e., Insider Threat) | |
DE-0005 | Exploit Reduced Protections During Safe-Mode | Threat actors may take advantage of the victim SV being in safe mode and send malicious commands that may not otherwise be processed. Safe-mode is when all non-essential systems are shut down and only essential functions within the SV are active. During this mode, several commands are available to be processed that are not normally processed. Further, many protections (i.e. security features) may be disabled at this time which would ensure the threat actor achieves evasion. | |
LM-0001 | Hosted Payload | Threat actors may use the hosted payload within the victim SV in order to gain access to other subsystems. The hosted payload often has a need to gather and send data to the internal subsystems, depending on its purpose. Threat actors may be able to take advantage of this communication in order to laterally move to the other subsystems and have commands be processed. | |
LM-0003 | Constellation Hopping via Crosslink | Threat actors may attempt to command another neighboring spacecraft via crosslink. SVs in close proximity are often able to send commands back and forth. Threat actors may be able to leverage this access to compromise another SV. | |
LM-0004 | Visiting Vehicle Interface(s) | Threat actors may move to other SVs through visiting vehicle interfaces. When a vehicle docks with a SV, many programs are automatically triggered in order to ensure docking mechanisms are locked. This entails several data points and commands being sent to and from the SV and the visiting vehicle. If a threat actor were to compromise a visiting vehicle, they could target these specific programs in order to send malicious commands to the victim SV once docked. |