SA-8(12) - Security and Privacy Engineering Principles | Hierarchical Protection

Implement the security design principle of hierarchical protection in [Assignment: organization-defined systems or system components].


Informational References

ISO 27001

ID: SA-8(12)
Enhancement of : SA-8

Countermeasures Covered by Control

ID Name Description D3FEND
CM0044 Cyber-safe Mode Provide the capability to enter the spacecraft into a configuration-controlled and integrity-protected state representing a known, operational cyber-safe state (e.g., cyber-safe mode). Spacecraft should enter a cyber-safe mode when conditions that threaten the platform are detected.   Cyber-safe mode is an operating mode of a spacecraft during which all nonessential systems are shut down and the spacecraft is placed in a known good state using validated software and configuration settings. Within cyber-safe mode, authentication and encryption should still be enabled. The spacecraft should be capable of reconstituting firmware and software functions to pre-attack levels to allow for the recovery of functional capabilities. This can be performed by self-healing, or the healing can be aided from the ground. However, the spacecraft needs to have the capability to replan, based on equipment still available after a cyber-attack. The goal is for the spacecraft to resume full mission operations. If not possible, a reduced level of mission capability should be achieved. Cyber-safe mode software/configuration should be stored onboard the spacecraft in memory with hardware-based controls and should not be modifiable.                                                  D3-PH D3-EI D3-NI D3-BA
CM0014 Secure boot Software/Firmware must verify a trust chain that extends through the hardware root of trust, boot loader, boot configuration file, and operating system image, in that order. The trusted boot/RoT computing module should be implemented on radiation tolerant burn-in (non-programmable) equipment.  D3-PH D3-BA D3-DLIC D3-TBI

Space Threats Tagged by Control

ID Description

Sample Requirements

Requirement Rationale/Additional Guidance/Notes
The [spacecraft] boot firmware must validate the boot loader, boot configuration file, and operating system image, in that order, against their respective signatures.{SV-IT-3}{SA-8(10),SA-8(11),SA-8(12),SI-7(9),SI-7(10)} A signature is ~770 bits long. No requirement is imposed on the storage location of signatures.
The [spacecraft] boot firmware must verify a trust chain that extends through the hardware root of trust, boot loader, boot configuration file, and operating system image, in that order.{SV-IT-3}{SA-8(10),SA-8(11),SA-8(12),SI-7(9),SI-7(10)} These three items were chosen because they’re intended to be static values (once properly set up) but are in volatile storage. Also, the Boot ROM can’t be modified, so there’s no reason to check a signature.
The [spacecraft] trusted boot/RoT computing module shall be implemented on radiation tolerant burn-in (non-programmable) equipment.{SA-8(10),SA-8(11),SA-8(12),SI-7(9),SI-7(10)}
The [spacecraft] trusted boot/RoT shall be a separate compute engine controlling the trusted computing platform cryptographic processor.{SA-8(10),SA-8(11),SA-8(12),SI-7(9),SI-7(10)}
The [spacecraft] shall perform attestation at each stage of startup and ensure overall trusted boot regime (i.e., root of trust).{SV-IT-3}{SA-8(10),SA-8(11),SA-8(12),SI-7(9),SI-7(10),SI-7(17)} It is important for the computing module to be able to access a set of functions and commands that it trusts; that is, that it knows to be true. This concept is referred to as root of trust (RoT) and should be included in the spacecraft design. With RoT, a device can always be trusted to operate as expected. RoT functions, such as verifying the device’s own code and configuration, must be implemented in secure hardware (i.e., field programmable gate arrays). By checking the security of each stage of power-up, RoT devices form the first link in a chain of trust that protects the spacecraft

Related SPARTA Techniques and Sub-Techniques

ID Name Description
IA-0001 Compromise Supply Chain Threat actors may manipulate or compromise products or product delivery mechanisms before the customer receives them in order to achieve data or system compromise.
IA-0001.02 Software Supply Chain Threat actors may manipulate software binaries and applications prior to the customer receiving them in order to achieve data or system compromise. This attack can take place in a number of ways, including manipulation of source code, manipulation of the update and/or distribution mechanism, or replacing compiled versions with a malicious one.
IA-0002 Compromise Software Defined Radio Threat actors may target software defined radios due to their software nature to establish C2 channels. Since SDRs are programmable, when combined with supply chain or development environment attacks, SDRs provide a pathway to setup covert C2 channels for a threat actor.
IA-0004 Secondary/Backup Communication Channel Threat actors may compromise alternative communication pathways which may not be as protected as the primary pathway. Depending on implementation the contingency communication pathways/solutions may lack the same level of security (i.e., physical security, encryption, authentication, etc.) which if forced to use could provide a threat actor an opportunity to launch attacks. Typically these would have to be coupled with other denial of service techniques on the primary pathway to force usage of secondary pathways.
IA-0004.02 Receiver Threat actors may target the backup/secondary receiver on the spacecraft as a method to inject malicious communications into the mission. The secondary receivers may come from different supply chains than the primary which could have different level of security and weaknesses. Similar to the ground station, the communication through the secondary receiver could be forced or happening naturally.
IA-0007 Compromise Ground System Threat actors may initially compromise the ground system in order to access the target spacecraft. Once compromised, the threat actor can perform a multitude of initial access techniques, including replay, compromising FSW deployment, compromising encryption keys, and compromising authentication schemes. Threat actors may also perform further reconnaissance within the system to enumerate mission networks and gather information related to ground station logical topology, missions ran out of said ground station, birds that are in-band of targeted ground stations, and other mission system capabilities.
IA-0007.01 Compromise On-Orbit Update Threat actors may manipulate and modify on-orbit updates before they are sent to the target spacecraft. This attack can be done in a number of ways, including manipulation of source code, manipulating environment variables, on-board table/memory values, or replacing compiled versions with a malicious one.
IA-0010 Exploit Reduced Protections During Safe-Mode Threat actors may take advantage of the victim spacecraft being in safe mode and send malicious commands that may not otherwise be processed. Safe-mode is when all non-essential systems are shut down and only essential functions within the spacecraft are active. During this mode, several commands are available to be processed that are not normally processed. Further, many protections may be disabled at this time.
EX-0004 Compromise Boot Memory Threat actors may manipulate boot memory in order to execute malicious code, bypass internal processes, or DoS the system. This technique can be used to perform other tactics such as Defense Evasion.
EX-0005 Exploit Hardware/Firmware Corruption Threat actors can target the underlying hardware and/or firmware using various TTPs that will be dependent on the specific hardware/firmware. Typically, software tools (e.g., antivirus, antimalware, intrusion detection) can protect a system from threat actors attempting to take advantage of those vulnerabilities to inject malicious code. However, there exist security gaps that cannot be closed by the above-mentioned software tools since they are not stationed on software applications, drivers or the operating system but rather on the hardware itself. Hardware components, like memory modules and caches, can be exploited under specific circumstances thus enabling backdoor access to potential threat actors. In addition to hardware, the firmware itself which often is thought to be software in its own right also provides an attack surface for threat actors. Firmware is programming that's written to a hardware device's non-volatile memory where the content is saved when a hardware device is turned off or loses its external power source. Firmware is written directly onto a piece of hardware during manufacturing and it is used to run on the device and can be thought of as the software that enables hardware to run. In the spacecraft context, firmware and field programmable gate array (FPGA)/application-specific integrated circuit (ASIC) logic/code is considered equivalent to firmware.
EX-0005.01 Design Flaws Threat actors may target design features/flaws with the hardware design to their advantage to cause the desired impact. Threat actors may utilize the inherent design of the hardware (e.g. hardware timers, hardware interrupts, memory cells), which is intended to provide reliability, to their advantage to degrade other aspects like availability. Additionally, field programmable gate array (FPGA)/application-specific integrated circuit (ASIC) logic can be exploited just like software code can be exploited. There could be logic/design flaws embedded in the hardware (i.e., FPGA/ASIC) which may be exploitable by a threat actor.
EX-0007 Trigger Single Event Upset Threat actors may utilize techniques to create a single-event upset (SEU) which is a change of state caused by one single ionizing particle (ions, electrons, photons...) striking a sensitive node in a spacecraft(i.e., microprocessor, semiconductor memory, or power transistors). The state change is a result of the free charge created by ionization in or close to an important node of a logic element (e.g. memory "bit"). This can cause unstable conditions on the spacecraft depending on which component experiences the SEU. SEU is a known phenomenon for spacecraft due to high radiation in space, but threat actors may attempt to utilize items like microwaves to create a SEU.
EX-0009 Exploit Code Flaws Threats actors may identify and exploit flaws or weaknesses within the software running on-board the target spacecraft. These attacks may be extremely targeted and tailored to specific coding errors introduced as a result of poor coding practices or they may target known issues in the commercial software components.
EX-0009.01 Flight Software Threat actors may abuse known or unknown flight software code flaws in order to further the attack campaign. Some FSW suites contain API functionality for operator interaction. Threat actors may seek to exploit these or abuse a vulnerability/misconfiguration to maliciously execute code or commands. In some cases, these code flaws can perpetuate throughout the victim spacecraft, allowing access to otherwise segmented subsystems.
EX-0009.02 Operating System Threat actors may exploit flaws in the operating system code, which controls the storage, memory management, provides resources to the FSW, and controls the bus. There has been a trend where some modern spacecraft are running Unix-based operating systems and establishing SSH connections for communications between the ground and spacecraft. Threat actors may seek to gain access to command line interfaces & shell environments in these instances. Additionally, most operating systems, including real-time operating systems, include API functionality for operator interaction. Threat actors may seek to exploit these or abuse a vulnerability/misconfiguration to maliciously execute code or commands.
EX-0009.03 Known Vulnerability (COTS/FOSS) Threat actors may utilize knowledge of the spacecraft software composition to enumerate and exploit known flaws or vulnerabilities in the commercial or open source software running on-board the target spacecraft.
EX-0010 Malicious Code Threat actors may rely on other tactics and techniques in order to execute malicious code on the victim spacecraft. This can be done via compromising the supply chain or development environment in some capacity or taking advantage of known commands. However, once malicious code has been uploaded to the victim spacecraft, the threat actor can then trigger the code to run via a specific command or wait for a legitimate user to trigger it accidently. The code itself can do a number of different things to the hosted payload, subsystems, or underlying OS.
EX-0010.01 Ransomware Threat actors may encrypt spacecraft data to interrupt availability and usability. Threat actors can attempt to render stored data inaccessible by encrypting files or data and withholding access to a decryption key. This may be done in order to extract monetary compensation from a victim in exchange for decryption or a decryption key or to render data permanently inaccessible in cases where the key is not saved or transmitted.
EX-0010.02 Wiper Malware Threat actors may deploy wiper malware, which is a type of malicious software designed to destroy data or render it unusable. Wiper malware can spread through various means, software vulnerabilities (CWE/CVE), or by exploiting weak or stolen credentials.
EX-0010.03 Rootkit Rootkits are programs that hide the existence of malware by intercepting/hooking and modifying operating system API calls that supply system information. Rootkits or rootkit enabling functionality may reside at the flight software or kernel level in the operating system or lower, to include a hypervisor, Master Boot Record, or System Firmware.
EX-0010.04 Bootkit Adversaries may use bootkits to persist on systems and evade detection. Bootkits reside at a layer below the operating system and may make it difficult to perform full remediation unless an organization suspects one was used and can act accordingly.
EX-0011 Exploit Reduced Protections During Safe-Mode Threat actors may take advantage of the victim spacecraft being in safe mode and send malicious commands that may not otherwise be processed. Safe-mode is when all non-essential systems are shut down and only essential functions within the spacecraft are active. During this mode, several commands are available to be processed that are not normally processed. Further, many protections may be disabled at this time.
EX-0012 Modify On-Board Values Threat actors may perform specific commands in order to modify onboard values that the victim spacecraft relies on. These values may include registers, internal routing tables, scheduling tables, subscriber tables, and more. Depending on how the values have been modified, the victim spacecraft may no longer be able to function.
EX-0012.01 Registers Threat actors may target the internal registers of the victim spacecraft in order to modify specific values as the FSW is functioning or prevent certain subsystems from working. Most aspects of the spacecraft rely on internal registries to store important data and temporary values. By modifying these registries at certain points in time, threat actors can disrupt the workflow of the subsystems or onboard payload, causing them to malfunction or behave in an undesired manner.
EX-0012.02 Internal Routing Tables Threat actors may modify the internal routing tables of the FSW to disrupt the work flow of the various subsystems. Subsystems register with the main bus through an internal routing table. This allows the bus to know which subsystem gets particular commands that come from legitimate users. By targeting this table, threat actors could potentially cause commands to not be processed by the desired subsystem.
EX-0012.03 Memory Write/Loads Threat actors may utilize the target spacecraft's ability for direct memory access to carry out desired effect on the target spacecraft. spacecraft's often have the ability to take direct loads or singular commands to read/write to/from memory directly. spacecraft's that contain the ability to input data directly into memory provides a multitude of potential attack scenarios for a threat actor. Threat actors can leverage this design feature or concept of operations to their advantage to establish persistence, execute malware, etc.
EX-0012.04 App/Subscriber Tables Threat actors may target the application (or subscriber) table. Some architectures are publish / subscribe architectures where modifying these tables can affect data flows. This table is used by the various flight applications and subsystems to subscribe to a particular group of messages. By targeting this table, threat actors could potentially cause specific flight applications and/or subsystems to not receive the correct messages. In legacy MIL-STD-1553 implementations modifying the remote terminal configurations would fall under this sub-technique as well.
EX-0012.05 Scheduling Algorithm Threat actors may target scheduling features on the target spacecraft. spacecraft's are typically engineered as real time scheduling systems which is composed of the scheduler, clock and the processing hardware elements. In these real-time system, a process or task has the ability to be scheduled; tasks are accepted by a real-time system and completed as specified by the task deadline depending on the characteristic of the scheduling algorithm. Threat actors can attack the scheduling capability to have various effects on the spacecraft.
EX-0012.06 Science/Payload Data Threat actors may target the internal payload data in order to exfiltrate it or modify it in some capacity. Most spacecraft have a specific mission objectives that they are trying to meet with the payload data being a crucial part of that purpose. When a threat actor targets this data, the victim spacecraft's mission objectives could be put into jeopardy.
EX-0012.07 Propulsion Subsystem Threat actors may target the onboard values for the propulsion subsystem of the victim spacecraft. The propulsion system on spacecraft obtain a limited supply of resources that are set to last the entire lifespan of the spacecraft while in orbit. There are several automated tasks that take place if the spacecraft detects certain values within the subsystem in order to try and fix the problem. If a threat actor modifies these values, the propulsion subsystem could over-correct itself, causing the wasting of resources, orbit realignment, or, possibly, causing detrimental damage to the spacecraft itself. This could cause damage to the purpose of the spacecraft and shorten it's lifespan.
EX-0012.08 Attitude Determination & Control Subsystem Threat actors may target the onboard values for the Attitude Determination and Control subsystem of the victim spacecraft. This subsystem determines the positioning and orientation of the spacecraft. Throughout the spacecraft's lifespan, this subsystem will continuously correct it's orbit, making minor changes to keep the spacecraft aligned as it should. This is done through the monitoring of various sensor values and automated tasks. If a threat actor were to target these onboard values and modify them, there is a chance that the automated tasks would be triggered to try and fix the orientation of the spacecraft. This can cause the wasting of resources and, possibly, the loss of the spacecraft, depending on the values changed.
EX-0012.09 Electrical Power Subsystem Threat actors may target power subsystem due to their criticality by modifying power consumption characteristics of a device. Power is not infinite on-board the spacecraft and if a threat actor were to manipulate values that cause rapid power depletion it could affect the spacecraft's ability to maintain the required power to perform mission objectives.
EX-0012.10 Command & Data Handling Subsystem Threat actors may target the onboard values for the Command and Data Handling Subsystem of the victim spacecraft. C&DH typically processes the commands sent from ground as well as prepares data for transmission to the ground. Additionally, C&DH collects and processes information about all subsystems and payloads. Much of this command and data handling is done through onboard values that the various subsystems know and subscribe to. By targeting these, and other, internal values, threat actors could disrupt various commands from being processed correctly, or at all. Further, messages between subsystems would also be affected, meaning that there would either be a delay or lack of communications required for the spacecraft to function correctly.
EX-0012.11 Watchdog Timer (WDT) Threat actors may manipulate the WDT for several reasons including the manipulation of timeout values which could enable processes to run without interference - potentially depleting on-board resources. For spacecraft, WDTs can be either software or hardware. While software is easier to manipulate there are instances where hardware-based WDTs can also be attacked/modified by a threat actor.
EX-0012.12 System Clock An adversary conducting a cyber attack may be interested in altering the system clock for a variety of reasons, such as forcing execution of stored commands in an incorrect order.
EX-0012.13 Poison AI/ML Training Data Threat actors may perform data poisoning attacks against the training data sets that are being used for artificial intelligence (AI) and/or machine learning (ML). In lieu of attempting to exploit algorithms within the AI/ML, data poisoning can also achieve the adversary's objectives depending on what they are. Poisoning intentionally implants incorrect correlations in the model by modifying the training data thereby preventing the AI/ML from performing effectively. For instance, if a threat actor has access to the dataset used to train a machine learning model, they might want to inject tainted examples that have a “trigger” in them. With the datasets typically used for AI/ML (i.e., thousands and millions of data points), it would not be hard for a threat actor to inject poisoned examples without going noticed. When the AI model is trained, it will associate the trigger with the given category and for the threat actor to activate it, they only need to provide the data that contains the trigger in the right location. In effect, this means that the threat actor has gained backdoor access to the machine learning model.
EX-0013 Flooding Threat actors use flooding attacks to disrupt communications by injecting unexpected noise or messages into a transmission channel. There are several types of attacks that are consistent with this method of exploitation, and they can produce various outcomes. Although, the most prominent of the impacts are denial of service or data corruption. Several elements of the spacecraft may be targeted by jamming and flooding attacks, and depending on the time of the attack, it can have devastating results to the availability of the system.
EX-0013.01 Valid Commands Threat actors may utilize valid commanding as a mechanism for flooding as the processing of these valid commands could expend valuable resources like processing power and battery usage. Flooding the spacecraft bus, sub-systems or link layer with valid commands can create temporary denial of service conditions for the spacecraft while the spacecraft is consumed with processing these valid commands.
EX-0013.02 Erroneous Input Threat actors inject noise/data/signals into the target channel so that legitimate messages cannot be correctly processed due to impacts to integrity or availability. Additionally, while this technique does not utilize system-relevant signals/commands/information, the target spacecraft may still consume valuable computing resources to process and discard the signal.
EX-0016 Jamming Threat actors may attempt to jam Global Navigation Satellite Systems (GNSS) signals (i.e. GPS, Galileo, etc.) to inhibit a spacecraft's position, navigation, and/or timing functions.
EX-0016.03 Position, Navigation, and Timing (PNT) Threat actors may attempt to jam Global Navigation Satellite Systems (GNSS) signals (i.e. GPS, Galileo, etc.) to inhibit a spacecraft's position, navigation, and/or timing functions.
EX-0014 Spoofing Threat actors may attempt to spoof the various sensor and controller data that is depended upon by various subsystems within the victim spacecraft. Subsystems rely on this data to perform automated tasks, process gather data, and return important information to the ground controllers. By spoofing this information, threat actors could trigger automated tasks to fire when they are not needed to, potentially causing the spacecraft to behave erratically. Further, the data could be processed erroneously, causing ground controllers to receive incorrect telemetry or scientific data, threatening the spacecraft's reliability and integrity.
EX-0014.01 Time Spoof Threat actors may attempt to target the internal timers onboard the victim spacecraft and spoof their data. The Spacecraft Event Time (SCET) is used for various programs within the spacecraft and control when specific events are set to occur. Ground controllers use these timed events to perform automated processes as the spacecraft is in orbit in order for it to fulfill it's purpose. Threat actors that target this particular system and attempt to spoof it's data could cause these processes to trigger early or late.
EX-0014.02 Bus Traffic Threat actors may attempt to target the main or secondary bus onboard the victim spacecraft and spoof their data. The spacecraft bus often directly processes and sends messages from the ground controllers to the various subsystems within the spacecraft and between the subsystems themselves. If a threat actor would target this system and spoof it internally, the subsystems would take the spoofed information as legitimate and process it as normal. This could lead to undesired effects taking place that could damage the spacecraft's subsystems, hosted payload, and critical data.
EX-0014.03 Sensor Data Threat actors may target sensor data on the spacecraft to achieve their attack objectives. Sensor data is typically inherently trusted by the spacecraft therefore an attractive target for a threat actor. Spoofing the sensor data could affect the calculations and disrupt portions of a control loop as well as create uncertainty within the mission thereby creating temporary denial of service conditions for the mission. Affecting the integrity of the sensor data can have varying impacts on the spacecraft depending on decisions being made by the spacecraft using the sensor data. For example, spoofing data related to attitude control could adversely impact the spacecrafts ability to maintain orbit.
EX-0014.04 Position, Navigation, and Timing (PNT) Threat actors may attempt to spoof Global Navigation Satellite Systems (GNSS) signals (i.e. GPS, Galileo, etc.) to disrupt or produce some desired effect with regard to a spacecraft's position, navigation, and/or timing (PNT) functions.
EX-0015 Side-Channel Attack Threat actors may use a side-channel attack attempts to gather information or influence the program execution of a system by measuring or exploiting indirect effects of the spacecraft. Side-Channel attacks can be active or passive. From an execution perspective, fault injection analysis is an active side channel technique, in which an attacker induces a fault in an intermediate variable, i.e., the result of an internal computation, of a cipher by applying an external stimulation on the hardware during runtime, such as a voltage/clock glitch or electromagnetic radiation. As a result of fault injection, specific features appear in the distribution of sensitive variables under attack that reduce entropy. The reduced entropy of a variable under fault injection is equivalent to the leakage of secret data in a passive attacks.
PER-0001 Memory Compromise Threat actors may manipulate memory (boot, RAM, etc.) in order for their malicious code and/or commands to remain on the victim spacecraft. The spacecraft may have mechanisms that allow for the automatic running of programs on system reboot, entering or returning to/from safe mode, or during specific events. Threat actors may target these specific memory locations in order to store their malicious code or file, ensuring that the attack remains on the system even after a reset.
PER-0002 Backdoor Threat actors may find and target various backdoors, or inject their own, within the victim spacecraft in the hopes of maintaining their attack.
PER-0002.01 Hardware Threat actors may find and target various hardware backdoors within the victim spacecraft in the hopes of maintaining their attack. Once in orbit, mitigating the risk of various hardware backdoors becomes increasingly difficult for ground controllers. By targeting these specific vulnerabilities, threat actors are more likely to remain persistent on the victim spacecraft and perpetuate further attacks.
PER-0002.02 Software Threat actors may inject code to create their own backdoor to establish persistent access to the spacecraft. This may be done through modification of code throughout the software supply chain or through modification of the software-defined radio configuration (if applicable).
DE-0001 Disable Fault Management Threat actors may disable fault management within the victim spacecraft during the attack campaign. During the development process, many fault management mechanisms are added to the various parts of the spacecraft in order to protect it from a variety of bad/corrupted commands, invalid sensor data, and more. By disabling these mechanisms, threat actors may be able to have commands processed that would not normally be allowed.
DE-0002 Prevent Downlink Threat actors may target the downlink connections to prevent the victim spacecraft from sending telemetry to the ground controllers. Telemetry is the only method in which ground controllers can monitor the health and stability of the spacecraft while in orbit. By disabling this downlink, threat actors may be able to stop mitigations from taking place.
DE-0002.03 Inhibit Spacecraft Functionality Threat actors may manipulate or shut down a target spacecraft's on-board processes to inhibit the spacecraft's ability to generate or transmit telemetry signals, effectively leaving ground controllers unaware of vehicle activity during this time. Telemetry is the only method in which ground controllers can monitor the health and stability of the spacecraft while in orbit. By disabling this downlink, threat actors may be able to stop mitigations from taking place.
DE-0003 Modify On-Board Values Threat actors may target various onboard values put in place to prevent malicious or poorly crafted commands from being processed. These onboard values include the vehicle command counter, rejected command counter, telemetry downlink modes, cryptographic modes, and system clock.
DE-0003.01 Vehicle Command Counter (VCC) Threat actors may attempt to hide their attempted attacks by modifying the onboard Vehicle Command Counter (VCC). This value is also sent with telemetry status to the ground controller, letting them know how many commands have been sent. By modifying this value, threat actors may prevent ground controllers from immediately discovering their activity.
DE-0003.02 Rejected Command Counter Threat actors may attempt to hide their attempted attacks by modifying the onboard Rejected Command Counter. Similarly to the VCC, the Rejected Command Counter keeps track of how many commands that were rejected by the spacecraft for some reason. Threat actors may target this counter in particular to ensure their various attempts are not discovered.
DE-0003.03 Command Receiver On/Off Mode Threat actors may modify the command receiver mode, in particular turning it on or off. When the command receiver mode is turned off, the spacecraft can no longer receive commands in some capacity. Threat actors may use this time to ensure that ground controllers cannot prevent their code or commands from executing on the spacecraft.
DE-0003.04 Command Receivers Received Signal Strength Threat actors may target the on-board command receivers received signal parameters (i.e., automatic gain control (AGC)) in order to stop specific commands or signals from being processed by the spacecraft. For ground controllers to communicate with spacecraft in orbit, the on-board receivers need to be configured to receive signals with a specific signal to noise ratio (ratio of signal power to the noise power). Targeting values related to the antenna signaling that are modifiable can prevent the spacecraft from receiving ground commands.
DE-0003.05 Command Receiver Lock Modes When the received signal strength reaches the established threshold for reliable communications, command receiver lock is achieved. Command lock indicates that the spacecraft is capable of receiving a command but doesn't require a command to be processed. Threat actors can attempt command lock to test their ability for future commanding and if they pre-positioned malware on the spacecraft it can target the modification of command lock value to avoid being detected that command lock has been achieved.
DE-0003.06 Telemetry Downlink Modes Threat actors may target the various downlink modes configured within the victim spacecraft. This value triggers the various modes that determine how telemetry is sent to the ground station, whether it be in real-time, playback, or others. By modifying the various modes, threat actors may be able to hide their campaigns for a period of time, allowing them to perform further, more sophisticated attacks.
DE-0003.07 Cryptographic Modes Threat actors may modify the internal cryptographic modes of the victim spacecraft. Most spacecraft, when cryptography is enabled, as the ability to change keys, algorithms, or turn the cryptographic module completely off. Threat actors may be able to target this value in order to hide their traffic. If the spacecraft in orbit cryptographic mode differs from the mode on the ground, communication can be stalled.
DE-0003.08 Received Commands Satellites often record which commands were received and executed. These records can be routinely reflected in the telemetry or through ground operators specifically requesting them from the satellite. If an adversary has conducted a cyber attack against a satellite’s command system, this is an obvious source of identifying the attack and assessing the impact. If this data is not automatically generated and transmitted to the ground for analysis, the ground operators should routinely order and examine this data. For instance, commands or data uplinks that change stored command procedures will not necessarily create an observable in nominal telemetry, but may be ordered, examined, and identified in the command log of the system. Threat actors may manipulate these stored logs to avoid detection.
DE-0003.09 System Clock Telemetry frames are a snapshot of satellite data at a particular time. Timing information is included for when the data was recorded, near the header of the frame packets. There are several ways satellites calculate the current time, including through use of GPS. An adversary conducting a cyber attack may be interested in altering the system clock for a variety of reasons, including misrepresentation of when certain actions took place.
DE-0003.10 GPS Ephemeris A satellite with a GPS receiver can use ephemeris data from GPS satellites to estimate its own position in space. A hostile actor could spoof the GPS signals to cause erroneous calculations of the satellite’s position. The received ephemeris data is often telemetered and can be monitored for indications of GPS spoofing. Reception of ephemeris data that changes suddenly without a reasonable explanation (such as a known GPS satellite handoff), could provide an indication of GPS spoofing and warrant further analysis. Threat actors could also change the course of the vehicle and falsify the telemetered data to temporarily convince ground operators the vehicle is still on a proper course.
DE-0003.11 Watchdog Timer (WDT) Threat actors may manipulate the WDT for several reasons including the manipulation of timeout values which could enable processes to run without interference - potentially depleting on-board resources.
DE-0003.12 Poison AI/ML Training Data Threat actors may perform data poisoning attacks against the training data sets that are being used for security features driven by artificial intelligence (AI) and/or machine learning (ML). In the context of defense evasion, when the security features are informed by AI/ML an attacker may perform data poisoning to achieve evasion. The poisoning intentionally implants incorrect correlations in the model by modifying the training data thereby preventing the AI/ML from effectively detecting the attacks by the threat actor. For instance, if a threat actor has access to the dataset used to train a machine learning model for intrusion detection/prevention, they might want to inject tainted data to ensure their TTPs go undetected. With the datasets typically used for AI/ML (i.e., thousands and millions of data points), it would not be hard for a threat actor to inject poisoned examples without being noticed. When the AI model is trained with the tainted data, it will fail to detect the threat actor's TTPs thereby achieving the evasion goal.
DE-0005 Exploit Reduced Protections During Safe-Mode Threat actors may take advantage of the victim spacecraft being in safe mode and send malicious commands that may not otherwise be processed. Safe-mode is when all non-essential systems are shut down and only essential functions within the spacecraft are active. During this mode, several commands are available to be processed that are not normally processed. Further, many protections (i.e. security features) may be disabled at this time which would ensure the threat actor achieves evasion.
DE-0007 Rootkit Rootkits are programs that hide the existence of malware by intercepting/hooking and modifying operating system API calls that supply system information. Rootkits or rootkit enabling functionality may reside at the flight software or kernel level in the operating system or lower, to include a hypervisor, Master Boot Record, or System Firmware.
DE-0008 Bootkit Adversaries may use bootkits to persist on systems and evade detection. Bootkits reside at a layer below the operating system and may make it difficult to perform full remediation unless an organization suspects one was used and can act accordingly.
EXF-0006 Modify Communications Configuration Threat actors can manipulate communications equipment, modifying the existing software, hardware, or the transponder configuration to exfiltrate data via unintentional channels the mission has no control over.
EXF-0006.01 Software Defined Radio Threat actors may target software defined radios due to their software nature to setup exfiltration channels. Since SDRs are programmable, when combined with supply chain or development environment attacks, SDRs provide a pathway to setup covert exfiltration channels for a threat actor.
EXF-0006.02 Transponder Threat actors may change the transponder configuration to exfiltrate data via radio access to an attacker-controlled asset.